The cooling system of the FC system controls the FC stack temperature so that it can remain at optimum for power generation.
The 2 coolant temperature sensors are used to monitor coolant temperatures at the FC stack outlet, which has increased due to FC stack cooling, and at the radiator outlet, which has been decreased by the radiator, for controlling the FC system temperature at a proper level.
For the circuit diagram, refer to DTC P1D2F00.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D2F00
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1D2A1C | FC Stack Outlet Coolant Temperature Sensor Circuit Voltage Out of Range | When the air conditioning coolant passage and FC coolant passage are connected, the FC stack coolant temperature (FC stack outlet) and the coolant temperature sensor value for air conditioning are significantly different.
(3 trip detection logic) |
·
Water temperature sensor (for FC stack outlet side) ·
Water temperature sensor (for radiator outlet side) |
Master Warning: Comes on | EV | B |
| Vehicle Condition | FC shutdown
(Ignition Switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | - | - | ○ | ○ | ○ | - |
By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.
| DTC No. | Data List |
|---|---|
| P1D2A1C | ·
FC Stack Outlet Coolant Temperature (Filtered Value) ·
Radiator Outlet Coolant Temperature (Filtered Value) |
| DTC No. | Active Test |
|---|---|
| P1D2A1C | Control the Radiator Rotary Valve |
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After performing repairs, clear the DTCs, perform the following procedure, and then check the data list items "Radiator Outlet Coolant Temperature (Filtered Value)" and "FC Stack Outlet Coolant Temperature (Filtered Value)".
Turn the ignition switch off, and leave the vehicle for at least 8 hours in an environment with an ambient temperature of more than 10°C (50°F).
The coolant passage which is monitored by the water temperature sensor (radiator outlet) is easily influenced by ambient air, and the temperature decreases significantly. For that reason, if the ambient temperature is less than 10°C (50°F), the temperature sensor value will significantly deviate from the water temperature sensor (FC stack outlet) value, as a result, these sensor values cannot be compared each other.
Check that the difference between the "Radiator Outlet Coolant Temperature (Filtered Value)" and the "FC Stack Outlet Coolant Temperature (Filtered Value)" is less than 10°C (18°F).
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Pre-procedure1
None
Procedure1
According to the display on the GTS, check for DTCs in the Health Check.
| Result | Proceed to |
|---|---|
| Only P1D2A1C is output | A |
| P1D2A1C is output and DTCs other than the DTCs in the table below are output | B |
| P1D2A1C is output and any DTCs in the table below are output | C |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P1D2A11 (EV) | FC Stack Outlet Coolant Temperature Sensor Circuit Short to Ground |
| P1D2A15 (EV) | FC Stack Outlet Coolant Temperature Sensor Circuit Short to Battery or Open | |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for 10 minutes or more.
NEXT
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Pre-procedure1
None
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B1414 is output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>FC CONTROL>WATER TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>FC CONTROL>WATER TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG