Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1F6E71  Air Pressure Regulating Valve Actuator Stuck  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1F6E71 Air Pressure Regulating Valve Actuator Stuck The operation duty signal of the FC air pressure regulator assembly (air pressure regulating valve) increases abnormally and the value of the valve opening angle sensor does not change for a certain amount of time
(1 trip detection logic)
·

FC air pressure regulator assembly (air pressure regulating valve)

·

Wire harness or connector


Master Warning: Comes on EV B

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ ○

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1F6E71
·

Target Air Pressure Regulating Valve Position

·

Air Pressure Regulating Valve Position



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 5 seconds or more.

2.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1F6E71 is output A
P1F6E71 is output and DTCs other than the DTCs in the table below are output B
P1F6E71 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1E7C18 (FC) Air Pressure Regulating Valve Circuit Current Below Threshold
P1E7C19 (FC) Air Pressure Regulating Valve Circuit Current Above Threshold
P1E7D11 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Ground
P1E7D15 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Battery or Open


HINT:

DTC P1F6E71 may be store due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE))

B

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE))

C

GO TO DTC CHART

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.
A476969

Disconnect the FC air pressure regulator assembly (air pressure regulating valve) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B16,B1)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B16)Engine Compartment>No. 2 Stack Wire>FC Air Pressure Regulator Assembly (Air Pressure Regulation Valve)

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

A48-20 (AVV1) - B16-6 (AVV1) Always Below 1 Ω
A48-1 (AVV2) - B16-5 (AVV2) Always Below 1 Ω
B1-74 (AVP) - B16-4 (AVP) Always Below 1 Ω
B1-73 (GAVP) - B16-3 (GAVP) Always Below 1 Ω
B1-72 (VAVP) - B16-2 (VAVP) Always Below 1 Ω
A48-20 (AVV1) or B16-6 (AVV1) - Body ground and other terminals Always 10 kΩ or higher
A48-1 (AVV2) or B16-5 (AVV2) - Body ground and other terminals Always 10 kΩ or higher
B1-74 (AVP) or B16-4 (AVP) - Body ground and other terminals Always 10 kΩ or higher
B1-73 (GAVP) or B16-3 (GAVP) - Body ground and other terminals Always 10 kΩ or higher
B1-72 (VAVP) or B16-2 (VAVP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air pressure regulator assembly (air pressure regulating valve) connector.


b.

Reconnect the FC control ECU connector.



OK

3.REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 5 seconds or more.


Procedure1

a.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.


b.

Confirm that the DTC is not output again.

Powertrain > EV > Trouble Codes
50001 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

END