Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  U149257  Software incompatibility with Hybrid/EV Powertrain Control Module Invalid/Incompatible Software Component  


DESCRIPTION

The hydrogen fuel control ECU compares the hydrogen tank assembly quantity stored value, the hydrogen tank assembly quantity recognized value and the hydrogen tank assembly quantity received value from the EV control ECU to determine whether there are differences in the values.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
U149257 Software incompatibility with Hybrid/EV Powertrain Control Module Invalid/Incompatible Software Component No +B low voltage when ignition switch is ON, and either of the following conditions is met for 10 seconds or more continuously
·

The hydrogen tank assembly quantity stored value, the hydrogen tank assembly quantity recognized value and the hydrogen tank assembly quantity received value from the EV control ECU do not match

·

The hydrogen tank assembly quantity stored value is an abnormal value

·

The hydrogen tank assembly quantity stored value is the initial value


(1 trip detection logic)
·

No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3)

·

EV control ECU

·

Hydrogen fuel control ECU assembly

·

Wire harness or connector


Master Warning: Comes on Hydrogen Filling Control A

Related Data List
DTC No. Data List
U149257
·

Number of Tanks (Memory)

·

Number of Tanks (Hybrid/EV Control)

·

Number of Tanks (Recognition)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 1 minute or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 HYDROGEN TANK ASSEMBLY CONNECTOR)
a.
A476966

Check the connection condition of the No. 3 hydrogen tank assembly connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.READ VALUE USING GTS (HYDROGEN TANK 3 TEMPERATURE SENSOR VOLTAGE)

B

17.CONNECT SECURELY

C

18.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.READ VALUE USING GTS (HYDROGEN TANK 3 TEMPERATURE SENSOR VOLTAGE)
a.

Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 3 Temperature Sensor Voltage
50003 494 28
Result:
Result Proceed to
The value of Hydrogen Tank 3 Temperature Sensor Voltage is 0.1 V or more, and 4.9 V or less A
The value of Hydrogen Tank 3 Temperature Sensor Voltage is more than 4.9 V B
The value of Hydrogen Tank 3 Temperature Sensor Voltage is less than 0.1 V C




A

3.READ VALUE USING GTS (NUMBER OF TANKS (HYBRID/EV CONTROL))

B

7.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

C

12.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
3.READ VALUE USING GTS (NUMBER OF TANKS (HYBRID/EV CONTROL))
a.

Check the hydrogen tank assembly installed quantity of the vehicle.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Number of Tanks (Hybrid/EV Control)
50003 494 14

b.

Read the value displayed on the GTS.

Result:
Result Proceed to
The installed quantity matches the Data List display A
The installed quantity does not match the Data List display B




A

4.PERFORM NUMBER OF TANKS INITIALIZATION

B

4.PERFORM NUMBER OF TANKS INITIALIZATION
Powertrain > Hydrogen Filling Control > Utility
Tester Display
Number of Tanks Initialization
50005 494 4698
Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > Hydrogen Filling Control > Clear DTCs
50002 494
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 1 minute or more.


Procedure1

a.

Check for DTCs.

Powertrain > Hydrogen Filling Control > Trouble Codes
50001 494
Result:
Result Proceed to
U149257 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

B

END

7.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.
A476966

Disconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3) connector.


b.
A335349C15
0.271,2.625 0.771,2.875 0.5,0.25 0.969,3.188 1.479,2.688 true 2.042,2.677 2.625,3.177 true 0.729,0.438 1.042,0.635 0.313,0.198 10 false *1 2.646,0.24 2.958,0.438 0.313,0.198 10 false *2 0.823,2.094 1.135,2.292 0.313,0.198 10 false *a 0.708,3.24 1.125,3.417 0.417,0.177 10 false TNT3 2.49,3.219 2.938,3.396 0.448,0.177 10 false GTT3 0.448,2.667 0.802,2.958 0.354,0.292 10 false G1
*1 No. 3 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 3)
*2 Hydrogen Fuel Control ECU Assembly
*a Front view of wire harness connector
(to No. 3 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 3)


Connect terminals 1 (TNT3) and 3 (GTT3) of the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3) connector on the wire harness side.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 3 Temperature Sensor Voltage
50003 494 28

Result:
Result Proceed to
The value of Hydrogen Tank 3 Temperature Sensor Voltage is less than 0.1 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3) connector.



A

8.REPLACE NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3)

B

9.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3))
8.REPLACE NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3)

NEXT

19.CLEAR DTC
9.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3))

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.

Disconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,G1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(G1)Body>Floor Wire / No. 3 Floor Wire>No. 3 Hydrogen Tank Assembly

G4-34 (TNT3) - G1-1 (TNT3) Always Below 1 Ω
G4-35 (GTT3) - G1-3 (GTT3) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


b.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

10.REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FUEL>HYDROGEN FUEL CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
12.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A476966

Disconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3) connector.


Procedure1

a.
A335356C06
0.729,0.469 1.042,0.667 0.313,0.198 10 false *1 2.615,0.292 2.927,0.49 0.313,0.198 10 false *2
*1 No. 3 Hydrogen Tank Assembly (Hydrogen Tank Temperature Sensor 3)
*2 Hydrogen Fuel Control ECU Assembly


Read the value displayed on the GTS.

Powertrain > Hydrogen Filling Control > Data List
Tester Display
Hydrogen Tank 3 Temperature Sensor Voltage
50003 494 28

Result:
Result Proceed to
The value of Hydrogen Tank 3 Temperature Sensor Voltage is more than 4.9 V A
None of the above conditions are met B


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor 3) connector.



A

13.REPLACE NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3)

B

14.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3))
13.REPLACE NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3)

NEXT

19.CLEAR DTC
14.CHECK HARNESS AND CONNECTOR (HYDROGEN FUEL CONTROL ECU ASSEMBLY - NO. 3 HYDROGEN TANK ASSEMBLY (HYDROGEN TANK TEMPERATURE SENSOR 3))

Pre-procedure1

a.

Disconnect the hydrogen fuel control ECU assembly connector.


b.

Disconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G4,G1)Location & Routing

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

Click Connector(G1)Body>Floor Wire / No. 3 Floor Wire>No. 3 Hydrogen Tank Assembly

G4-34 (TNT3) or G1-1 (TNT3) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 3 hydrogen tank assembly (hydrogen tank temperature sensor) connector.


b.

Reconnect the hydrogen fuel control ECU assembly connector.



OK

15.REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FUEL>HYDROGEN FUEL CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
17.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
18.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
19.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > Hydrogen Filling Control > Clear DTCs
50002 494
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

20.PERFORM NUMBER OF TANKS INITIALIZATION
20.PERFORM NUMBER OF TANKS INITIALIZATION
Powertrain > Hydrogen Filling Control > Utility
Tester Display
Number of Tanks Initialization
50005 494 4698
Result:
Proceed to
NEXT



NEXT

END