The FC boost control ECU is located inside the FC converter assembly. It monitors the reactor current sensors provided for each phase and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1D3028 | Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | Offset error is occurring in the FC converter current sensor (phase U current sensor)
(1 trip detection logic) |
·
FC boost control ECU ·
FC converter current sensor ·
ECU wire sub-assembly ·
No. 1 FC converter wire ·
Wire harness or connector |
Master Warning: Comes on | FCDC | B |
| P1D3528 | Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | Offset error is occurring in the FC converter current sensor (phase V current sensor)
(1 trip detection logic) |
·
FC boost control ECU ·
FC converter current sensor ·
ECU wire sub-assembly ·
No. 1 FC converter wire ·
Wire harness or connector |
Master Warning: Comes on | FCDC | B |
| P1D3A28 | Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | Offset error is occurring in the FC converter current sensor (phase W current sensor)
(1 trip detection logic) |
·
FC boost control ECU ·
FC converter current sensor ·
ECU wire sub-assembly ·
No. 1 FC converter wire ·
Wire harness or connector |
Master Warning: Comes on | FCDC | B |
| P1D4028 | Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | Offset error is occurring in the FC converter current sensor (phase X current sensor)
(1 trip detection logic) |
·
FC boost control ECU ·
FC converter current sensor ·
ECU wire sub-assembly ·
No. 1 FC converter wire ·
Wire harness or connector |
Master Warning: Comes on | FCDC | B |
| DTC No. | Data List |
|---|---|
| P1D3028 | ·
FC Voltage ·
FC Converter Output Voltage |
| P1D3528 | ·
FC Voltage ·
FC Converter Output Voltage |
| P1D3A28 | ·
FC Voltage ·
FC Converter Output Voltage |
| P1D4028 | ·
FC Voltage ·
FC Converter Output Voltage |
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.
Make sure to remove the EV supply battery assembly service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.
After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.
Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.
Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL
Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.
When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON (READY) and wait for 5 seconds or more.
Pre-procedure1
None
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P1D3028, P1D3528, P1D3A28 or P1D4028 is output | A |
| P1D3028, P1D3528, P1D3A28 or P1D4028 is output and DTCs other than the DTCs in the table below are output | B |
| P1D3028, P1D3528, P1D3A28 or P1D4028 is output and any DTCs in the table below are output | C |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Power source circuit malfunction | P1F651C | FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range |
| P1F661C | FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range | |
DTC P1D3028, P1D3528, P1D3A28 or P1D4028 may be output as a result of the malfunction indicated by the DTCs above.
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) | C |
A
Replace the FC converter and FC stack assembly components listed below.
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
FC boost control ECU
FC converter current sensor
ECU wire sub-assembly
No. 1 FC converter wire
Refer to the parts location for the FC converter and FC stack assembly components.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION
Refer to the system description for the parts location of the FC converter and FC stack assembly components.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION
B
C