Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D4F62  Total Reactor Current/FC Current Signal Compare Failure  


DESCRIPTION

The FC boost control ECU monitors the detection circuit inside the FC converter assembly and detects circuit malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D4F62 Total Reactor Current/FC Current Signal Compare Failure A malfunction in the adder circuit is detected because the difference between the total current of the reactors for all phases and the FC current is large.
(1 trip detection logic)
·

FC boost control ECU

·

FC converter current sensor

·

ECU wire sub-assembly

·

No. 1 FC converter wire


Master Warning: Comes on FCDC B

Related Data List
DTC No. Data List
P1D4F62 FC Current

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

Drive the vehicle for approximately 10 minutes referring to the following freeze frame data or Data List items: "Vehicle Speed".



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1D4F62 is output A
P1D4F62 and DTCs other than the DTCs in the table below are output B
P1D4F62 and any DTCs in the table below are output C


Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure

HINT:

DTC P1D4F62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC

C

GO TO DTC CHART

2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

3.READ VALUE USING GTS (PHASE U CURRENT, PHASE V CURRENT, PHASE W CURRENT, PHASE X CURRENT, FC CURRENT)
3.READ VALUE USING GTS (PHASE U CURRENT, PHASE V CURRENT, PHASE W CURRENT, PHASE X CURRENT, FC CURRENT)

Pre-procedure1

a.

None


Procedure1

a.

Read the Data List.

Powertrain > FCDC > Data List
Tester Display
FC Current
Phase U Current
Phase V Current
Phase W Current
Phase X Current
50003 493 11,18,27,36,45
Result:
Result Proceed to
Difference between "total of Phase U Current, Phase V Current, Phase W Current and Phase X Current" and "FC Current" is 15.0 A or higher A
Other than above B


HINT:

Instantaneous change due to noise, etc. is not included



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

FC boost control ECU

·

FC converter current sensor

·

ECU wire sub-assembly

·

No. 1 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




B

4.SIMULATION TEST
4.SIMULATION TEST
a.

Turn the ignition switch to ON (READY). (A)


b.

Accelerate the vehicle to approximately 80 km/h (50 mph). (B)


c.

While checking the Data List item "FC Current", depress the accelerator pedal and ensure that all conditions stated below are met. (C)

Powertrain > FCDC > Data List
Tester Display
FC Current
50003 493 11
CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Driving condition:

Data List item "FC Current" value remains 263 A or more for at least 2 seconds.


A336325E03
0.448,1.458 1.719,1.688 1.271,0.229 10 false 80 km/h (50 mph) 0.771,2.365 1.573,2.635 0.802,0.271 10 false READY ON 1.969,2.229 2.583,2.427 0.615,0.198 10 false (A) 3.021,1.354 3.635,1.552 0.615,0.198 10 false (B) 3.875,0.948 4.49,1.146 0.615,0.198 10 false (C) 3.448,2.969 4.698,3.177 1.25,0.208 10 false 2 seconds or more 4.76,3.323 5.99,3.5 1.229,0.177 10 false Check for DTCs


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (FCDC)
5.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
DTCs are not output A
Only P1D4F62 is output B
P1D4F62 and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure


HINT:

DTC P1D4F62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

B

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

FC boost control ECU

·

FC converter current sensor

·

ECU wire sub-assembly

·

No. 1 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




C

GO TO DTC CHART