Home › Engine / Hybrid System › FC CONTROL › FC STACK
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0449975 FC STACK J

FC CONTROL  FC STACK  Electrical Charge Self-discharge Work  


PROCEDURE

1.CHECK BEFORE PERFORMING ELECTRICAL CHARGE SELF-DISCHARGE
a.

Check that the FC stack assembly with FC converter with front frame assembly has been lowered from the vehicle.

CAUTION:

Since the stack voltage cannot be checked while it is installed in the vehicle, never perform the work without first lowering the FC stack assembly with FC converter with front frame assembly from the vehicle.



Result:
Result Proceed to
Lowered OK
Not lowered NG



OK

2.CHECK STACK VOLTAGE

NG

GO TO REMOVE FC STACK ASSEMBLY WITH FC CONVERTER WITH FRONT FRAME ASSEMBLY

2.CHECK STACK VOLTAGE
a.

Remove the front FC converter service hole cover.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


b.

Remove the No. 1 FC stack case plug.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


c.

Remove the FC converter vent cover.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


d.
A484127C01
1.698,1.01 2.104,1.75 2.104,1.75 2.365,1.75 true 2.031,3.698 2.594,4.031 2.594,4.031 2.771,4.031 true 0.063,0.052 0.344,0.281 0.281,0.229 12 true *A 0.052,2.385 0.365,2.635 0.313,0.25 12 true *B 2.396,1.646 2.625,1.885 0.229,0.24 10 true *a 2.802,3.927 3.052,4.156 0.25,0.229 10 true *b
*A Front Side
*B Rear Side
*a Positive Terminal
*b Negative Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Specified Condition
Front side (positive terminal) - rear side (negative terminal) Below 25 V



Result:
Proceed to
NEXT



NEXT

3.REMOVE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING)
3.REMOVE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING)
a.
A482333

Remove the 2 bolts and FC air pressure regulator assembly (air sealing valve).


b.
A482334

Remove the 2 gaskets from the FC stack air inlet pipe assembly and FC stack air and water inlet.


c.
A482335

To prevent contamination by foreign matter or water droplets, cover the connecting portions of the FC air pressure regulator assembly (air sealing valve) and FC stack air inlet pipe assembly with protective tape.


Result:
Proceed to
NEXT



NEXT

4.LEAVE VEHICLE AS IS FOR 2 HOURS
4.LEAVE VEHICLE AS IS FOR 2 HOURS
a.

Leave the vehicle as is for 2 hours.


Result:
Proceed to
NEXT



NEXT

5.REMOVE HYDROGEN SUPPLY PRESSURE REGULATOR ASSEMBLY
5.REMOVE HYDROGEN SUPPLY PRESSURE REGULATOR ASSEMBLY
a.

Remove the hydrogen supply pressure regulator assembly.

Click hereEngine / Hybrid System>FC CONTROL>HYDROGEN INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.REMOVE NO. 1 HYDROGEN TUBE AND NO. 2 HYDROGEN TUBE
6.REMOVE NO. 1 HYDROGEN TUBE AND NO. 2 HYDROGEN TUBE
a.
A482339

Remove the bolt and No. 1 hydrogen tube.


b.

Remove the O-ring from the No. 1 hydrogen tube.


c.

Cover the connection of the No. 1 hydrogen tube with plastic bags to prevent the foreign matter.


d.
A482340

Remove the 2 bolts and No. 2 hydrogen tube.


e.

Remove the 2 O-rings from the No. 2 hydrogen tube.


f.

Cover the connection of the No. 2 hydrogen tube with plastic bags to prevent the foreign matter.


Result:
Proceed to
NEXT



NEXT

7.LEAVE VEHICLE AS IS FOR 18 HOURS
7.LEAVE VEHICLE AS IS FOR 18 HOURS
a.

Leave the vehicle as is for 18 hours.


Result:
Proceed to
NEXT



NEXT

8.CHECK STACK VOLTAGE
8.CHECK STACK VOLTAGE
a.
A484127C01
1.698,1.01 2.104,1.75 2.104,1.75 2.365,1.75 true 2.031,3.698 2.594,4.031 2.594,4.031 2.771,4.031 true 0.063,0.052 0.344,0.281 0.281,0.229 12 true *A 0.052,2.385 0.365,2.635 0.313,0.25 12 true *B 2.396,1.646 2.625,1.885 0.229,0.24 10 true *a 2.802,3.927 3.052,4.156 0.25,0.229 10 true *b
*A Front Side
*B Rear Side
*a Positive Terminal
*b Negative Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Specified Condition
Front side (positive terminal) - rear side (negative terminal) Below 25 V


NOTICE:
·

If the voltage is not below 25 V, leave the vehicle until the voltage drops below 25 V.

·

Do not perform disassembly work until the voltage drops below 25 V.




Result:
Proceed to
NEXT



NEXT

END ELECTRICAL CHARGE SELF-DISCHARGE
a.

After ending electrical charge self-discharge, restart the procedure from "Step 169. Remove FC Air Pressure Regulator Assembly (Air Pressure Regulating Valve)".

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL