Home › Engine / Hybrid System › FC CONTROL › HYDROGEN INJECTOR
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466404 HYDROGEN INJECTOR A

FC CONTROL  HYDROGEN INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A484087N01
0.042,0.063 2.51,2.781 2.469,2.719 1.563,2.49 1.385,2.49 1.385,2.49 1.302,2.24 true 4.198,1.604 4.438,1.604 4.438,1.604 4.583,2.01 true 3.969,0.302 4.281,0.302 4.281,0.302 4.583,0.594 true 1.542,1.531 1.719,1.531 1.719,1.531 2.021,1.823 true 1.771,2.313 1.604,2.313 1.604,2.313 1.49,2.156 true 1.281,2.667 1.115,2.667 1.115,2.667 1.115,2.313 true 1.917,3.292 1.74,3.292 1.74,3.292 1.656,3.083 true 3.073,2.76 2.938,2.76 2.938,2.76 2.938,2.448 true 0.823,1.958 0.656,1.958 0.656,1.958 0.521,2.427 true 4.271,3.438 4.458,3.438 4.458,3.438 4.604,3.229 true 3.74,1.031 3.531,1.031 3.531,1.031 3.396,1.292 true 6.625,0.219 6.813,0.219 true 1.76,0.583 1.938,0.583 1.938,0.583 2.229,0.792 true 0.99,3.177 1.177,3.177 1.177,3.177 1.323,2.969 true 2.927,1.771 2.792,1.771 2.792,1.771 2.677,2.177 false 2.927,1.969 2.792,1.969 2.792,1.969 2.719,2.208 false 6.177,0.083 6.698,0.417 0.521,0.333 18 false 1, 2 3.792,0.188 4.052,0.51 0.26,0.323 18 false 3 4.021,1.479 4.281,1.802 0.26,0.323 18 false 4 0.365,0.104 0.625,0.427 0.26,0.323 18 false 5 1.583,0.458 1.844,0.781 0.26,0.323 18 false 6 1.594,2.354 1.854,2.677 0.26,0.323 18 false 7 5.177,1.594 5.531,1.823 0.354,0.229 10 false x 2 1.885,1.177 2.344,1.375 0.458,0.198 10 false x 3 1.823,2.208 2.281,2.406 0.458,0.198 10 false ● 1.323,2.552 1.781,2.75 0.458,0.198 10 false ●*7 3.125,2.698 3.583,2.896 0.458,0.198 10 false *3 0.875,1.896 1.333,2.094 0.458,0.198 10 false *5 4.771,2.552 5.229,2.75 0.458,0.198 10 false x 2 4.094,3.375 4.365,3.573 0.271,0.198 10 false *6 3.802,0.969 4.26,1.167 0.458,0.198 10 false *1 1.365,1.469 1.823,1.667 0.458,0.198 10 false *4 0.208,2.625 0.667,2.823 0.458,0.198 10 false x 2 1.958,3.219 2.417,3.417 0.458,0.198 10 false *2 1.135,2.323 1.594,2.521 0.458,0.198 10 false x 3 1.344,2.198 1.802,2.396 0.458,0.198 10 false x 3 1.573,2.073 2.031,2.271 0.458,0.198 10 false x 3 0.823,3.125 1.281,3.323 0.458,0.198 10 false ● 2.979,1.708 3.438,1.906 0.458,0.198 10 false ● 2.979,1.906 3.438,2.104 0.458,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAUTIONS FOR COMPRESSED HYDROGEN GAS - - - (Click here)
2 PRESSURE RELEASE OPERATION (for Low Pressure and Medium Pressure) - - - (Click here)
3 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
4 FC STACK COVER BRACKET 1A911 - - -
5 HYDROGEN SUPPLY PRESSURE REGULATOR ASSEMBLY 23A30 (Click here) - -
6 WIRE HARNESS CLAMP BRACKET - - - -
7 FUEL INJECTOR ASSEMBLY 23250H (Click here) - -

*1 NO. 1 HYDROGEN DETECTOR BRACKET *2 NO. 1 HYDROGEN TUBE
*3 NO. 1 HYDROGEN SUPPLY TUBE SUB-ASSEMBLY *4 HYDROGEN SUPPLY PRIMARY PIPE SUB-ASSEMBLY
*5 HYDROGEN SUPPLY SECONDARY PIPE SUB-ASSEMBLY *6 WIRE HARNESS
*7 INSULATOR - -
● Non-reusable part - -

PROCEDURE

Hide 1. CAUTIONS FOR COMPRESSED HYDROGEN GAS

Hide 2. PRESSURE RELEASE OPERATION (for Low Pressure and Medium Pressure)

Hide 1A906 3.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide 1A911 4.REMOVE FC STACK COVER BRACKET

a.
A475820


Hide 23A30 5.REMOVE HYDROGEN SUPPLY PRESSURE REGULATOR ASSEMBLY

a.
A475833C01
0.125,0.177 0.26,0.448 0.135,0.271 18 true i 2.531,0.177 2.688,0.448 0.156,0.271 18 true ii 4.875,0.177 5.073,0.448 0.198,0.271 18 true iii 0.333,1.917 0.531,2.156 0.198,0.24 18 true iv 2.5,1.958 2.74,2.24 0.24,0.281 18 true v 4.865,1.958 5.094,2.26 0.229,0.302 18 true vi 2.729,3.969 2.99,4.281 0.26,0.313 18 true vii
V113147

Shift
V113148

Pull Up


i.

Disconnect the 5 connectors and detach the 2 clamps.


ii.

Remove the bolt and disconnect the No. 1 hydrogen detector bracket.


iii.

Remove the 2 nuts and 2 bolts.


iv.

Remove the 3 bolts and hydrogen supply pressure regulator assembly from the No. 1 hydrogen tube and No. 1 hydrogen supply tube sub-assembly.


v.

Remove the O-ring from the No. 1 hydrogen tube.


vi.

Remove the O-ring from the No. 1 hydrogen supply tube sub-assembly.


vii.

Protect the openings of the No. 1 hydrogen tube, No. 1 hydrogen supply tube sub-assembly and hydrogen supply pressure regulator assembly with protective tape (non-residue type) to prevent the entry of foreign matter or water.



Hide 6.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A475821


Hide 23250H 7.REMOVE FUEL INJECTOR ASSEMBLY

a.
A475822N01
0.177,0.146 0.406,0.448 0.229,0.302 18 false i 2.885,0.135 3.115,0.438 0.229,0.302 18 false ii 5.01,0.135 5.24,0.438 0.229,0.302 18 false iii 1.729,2.188 1.958,2.49 0.229,0.302 18 false iv 4.219,2.135 4.448,2.438 0.229,0.302 18 false v

i.

Remove the 2 bolts and hydrogen supply secondary pipe sub-assembly.


ii.

Protect the openings of the hydrogen primary pipe sub-assembly with protective tape (non-residue type) to prevent the entry of foreign matter or water.


iii.

Remove the 3 fuel injector assemblies from the hydrogen supply secondary pipe sub-assembly.


iv.

Protect the openings of the hydrogen secondary pipe sub-assembly with protective tape (non-residue type) to prevent the entry of foreign matter or water.


v.

Remove the 3 O-rings and 3 insulators from the 3 fuel injector assemblies.