Home › Vehicle Interior › HEATING / AIR CONDITIONING › ION GENERATOR › from 2021.08
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0483272 ION GENERATOR A

HEATING / AIR CONDITIONING  ION GENERATOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E468041N01
2.104,2.365 3.958,3.323 1.854,0.958 3.479,2.604 3.698,2.604 false 3.156,4.208 3.667,4.208 false 2.51,2.615 2.667,2.615 2.667,2.615 2.833,2.76 false 2.552,3.135 2.448,2.99 2.448,2.99 2.323,2.99 false 5.188,1.156 5.594,0.656 5.594,0.656 5.771,0.656 false 1.854,2.885 2.104,2.885 false 3.49,2.813 3.75,3.031 0.26,0.219 10 false x 2 1.688,2.74 1.906,3.021 0.219,0.281 18 false 3 3,4.052 3.219,4.333 0.219,0.281 18 false 1 3.76,2.427 3.979,2.729 0.219,0.302 18 false 4 2.323,2.469 2.5,2.792 0.177,0.323 18 false 5 2.177,2.896 2.438,3.115 0.26,0.219 10 false *1 6.104,0.49 6.385,0.844 0.281,0.354 18 false 2 6.146,1.406 6.406,1.625 0.26,0.219 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTRUMENT PANEL SAFETY PAD ASSEMBLY - - - -
2 NO. 4 HEATER TO REGISTER DUCT 55846A - -
3 NO. 1 ION GENERATOR SUB-ASSEMBLY WITH NO. 1 ION GENERATOR BRACKET - - - -
4 AIR DUCT SUB-ASSEMBLY 87201N - - -
5 NO. 1 ION GENERATOR SUB-ASSEMBLY 88051B - - -

*1 NO. 1 ION GENERATOR BRACKET - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ion generator sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 55846A 2.REMOVE NO. 4 HEATER TO REGISTER DUCT

Z101186

Click here(Click here)

Hide 3.REMOVE NO. 1 ION GENERATOR SUB-ASSEMBLY WITH NO. 1 ION GENERATOR BRACKET

a.
E468043


Hide 87201N 4.REMOVE AIR DUCT SUB-ASSEMBLY

a.
E468044


Hide 88051B 5.REMOVE NO. 1 ION GENERATOR SUB-ASSEMBLY

a.
E468045