| ● | Non-reusable part | ★ | Precoated part |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 23 | FRONT SEAT ASSEMBLY LH | - | - | - | - |
| 24 | FRONT SEAT ASSEMBLY RH | - | - | - | - |
| *A | w/ Headup Display | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 42 | REAR NO. 2 AIR DUCT | 87212F | - | - | - |
| 43 | REAR NO. 1 AIR DUCT | 87212 | - | - | - |
| 44 | FRONT FLOOR MAT RH | 58511H | - | - | - |
| 45 | REAR NO. 4 AIR DUCT | 87212H | - | - | - |
| 46 | REAR NO. 3 AIR DUCT | 87212G | - | - | - |
| 47 | FRONT FLOOR MAT LH | 58512B | - | - | - |
| *A | w/o Ion Generator | *B | w/ Ion Generator |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 76 | AIR CONDITIONER UNIT ASSEMBLY | - | - | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioner unit assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. | - |
When removing the air conditioning radiator damper servo sub-assembly, reinstallation is easier to perform if the following conditions are set before disconnecting the negative (-) battery terminal.
| Item | Condition |
|---|---|
| Air vent damper position | Face |
| Set temperature | Max cool |
1. CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))
53291B
2.REMOVE RADIATOR COVER PLATE
53292A
3.REMOVE UPPER RADIATOR SUPPORT SEAL
53295
4.REMOVE LOWER RADIATOR AIR DEFLECTOR
5.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
51441N
6.REMOVE FRONT COMPARTMENT UNDER COVER
51219
7.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR
51420A
8.REMOVE FRONT COMPARTMEMT UNDER COVER ASSEMBLY
9.DRAIN COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-Mixed))
10.REMOVE FRONT WIPER MOTOR AND LINK
55752A
11.REMOVE COWL VENTILATOR SPLASH SHIELD LH
12.REMOVE HOLE PLUG
821H3A
13.DISCONNECT NO. 1 BATTERY PACK WIRE
821H1
14.DISCONNECT FLOOR UNDER WIRE
17A90
15.DISCONNECT FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
G9200A
16.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)
88704A
17.DISCONNECT SUCTION HOSE SUB-ASSEMBLY A
|
Remove in this Direction | - | - |
Remove the bolt.
Rotate the 1-point tightening plate and disconnect the suction hose sub-assembly A.
Remove the O-ring from the suction pipe sub-assembly A.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88G16M
18.DISCONNECT NO. 1 LIQUID TUBE
Disconnect the No. 1 liquid tube.
Remove the O-ring from the No. 1 liquid tube.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88897K
19.REMOVE COOLER PIPE GROMMET
87209E
20.DISCONNECT WATER HOSE SUB-ASSEMBLY E
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly E.
Do not apply excessive force to the water hose sub-assembly E.
Prepare a drain pan or cloth in case the coolant leaks.
87209C
21.DISCONNECT WATER HOSE SUB-ASSEMBLY C
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly C.
Do not apply excessive force to the water hose sub-assembly C.
Prepare a drain pan or cloth in case the coolant leaks.
88898D
22.REMOVE GROMMET
23.REMOVE FRONT SEAT ASSEMBLY LH
24.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
25.REMOVE INSTRUMENT PANEL SAFETY PAD
83108
26.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
45250
27.REMOVE STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
for Power Tilt and Power Telescopic Steering Column:
67918F
28.REMOVE REAR DOOR SCUFF PLATE INSIDE LH
62312B
29.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62332A
30.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
62414A
31.REMOVE LOWER CENTER PILLAR GARNISH LH
67917F
32.REMOVE REAR DOOR SCUFF PLATE INSIDE RH
Use the same procedure described for the LH side.
62311B
33.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62331A
34.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62413A
35.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
78118
36.REMOVE ACCELERATOR PEDAL PAD
87217B
38.REMOVE AIR DUCT PLUG
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the air duct plug.
Use the same procedure for the other side.
87212J
39.REMOVE REAR NO. 5 AIR DUCT
|
Remove in this Direction | - | - |
Use the same procedure for the other side.
58521C
40.REMOVE NO. 2 FLOOR CARPET HOOK
Using a clip remover with its tip wrapped with protective tape, detach the clamp and remove the 3 No. 2 floor hooks.
Use the same procedure for the other side.
58510C
41.REMOVE FRONT FLOOR FRONT CARPET ASSEMBLY
|
Pull Out |
|
Fold Up |
|
Fastener | - | - |
Using a clip remover, remove the clip.
Detach the claw.
Detach the 3 fasteners.
Remove some of the front floor front carpet assembly in the order shown in the illustration until the rear floor mat LH can be removed.
|
Pull Out |
|
Fold Up |
|
Fastener | - | - |
Using a clip remover, remove the clip.
Detach the claw.
Detach the fastener.
Remove some of the front floor front carpet assembly in the order shown in the illustration until the rear floor mat RH can be removed.
87212F
42.REMOVE REAR NO. 2 AIR DUCT
|
Remove in this Direction | - | - |
87212
43.REMOVE REAR NO. 1 AIR DUCT
|
Remove in this Direction | - | - |
58511H
44.REMOVE FRONT FLOOR MAT RH
87212H
45.REMOVE REAR NO. 4 AIR DUCT
|
Remove in this Direction | - | - |
87212G
46.REMOVE REAR NO. 3 AIR DUCT
|
Remove in this Direction | - | - |
58512B
47.REMOVE FRONT FLOOR MAT LH
87201F
48.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY
|
Remove in this Direction | - | - |
Using a clip remover, remove the clip and No. 3 air duct sub-assembly.
49.REMOVE EV CONTROL ECU WITH EV CONTROL ECU BRACKET
82730D
50.REMOVE PASSENGER SIDE JUNCTION BLOCK ASSEMBLY
|
Remove in this Direction |
|
Connector |
|
Lever Connector |
|
Nut |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.
Disconnect the 2 lever connectors and 2 connectors.
Remove the 2 nuts and passenger side junction block assembly.
|
Remove in this Direction | - | - |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.
Disconnect the 2 lever connectors.
Detach the clamp and claw.
82111C
51.DISCONNECT FRONT COMPARTMENT WIRE MAIN
894C1
52.REMOVE SHIFT CONTROL ECU
82715
54.REMOVE WIRING HARNESS CLAMP BRACKET
86240A
55.REMOVE STEREO COMPONENT EQUALIZER ASSEMBLY
55847B
56.REMOVE NO. 5 HEATER TO REGISTER DUCT
Using a clip remover, remove the 3 clips and No. 5 heater to register duct.
55972C
57.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
Using a clip remover, remove the clip.
Detach the clamp and claw and remove the No. 2 side defroster nozzle duct.
58.REMOVE NAVIGATION ECU ASSEMBLY WITH BRACKET
55990B
59.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
60.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET
55846A
61.REMOVE NO. 4 HEATER TO REGISTER DUCT
w/o Ion Generator:
Using a clip remover, remove the 2 clips and No. 4 heater to register duct.
w/ Ion Generator:
Using a clip remover, remove the 2 clips.
Detach the duct and remove the No. 4 heater to register duct.
62.REMOVE NO. 1 ION GENERATOR SUB-ASSEMBLY WITH NO. 1 ION GENERATOR BRACKET (w/ Ion Generator)
55381D
63.REMOVE NO. 1 INSTRUMENT PANEL SHIFT MOUNTING BRACKET
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
55307C
64.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Screw | - | - |
55306A
65.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Screw | - | - |
55845A
66.REMOVE NO. 3 HEATER TO REGISTER DUCT
Using a clip remover, remove the 3 clips and No. 3 heater to register duct.
55843A
67.REMOVE NO. 1 HEATER TO REGISTER DUCT
|
Clip |
|
Screw |
Using a clip remover, remove the 2 clips.
Remove the screw and No. 1 heater to register duct.
55308B
68.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
|
Bolt |
|
Nut |
70.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY WITH HEATER BRACKET
82141
71.DISCONNECT INSTRUMENT PANEL WIRE
The illustration is an example, so the details may differ.
|
Connector |
|
Nut |
88539N
72.REMOVE NO. 4 COOLER UNIT DRAIN HOSE
88539E
73.REMOVE NO. 3 COOLER UNIT DRAIN HOSE
88539G
74.REMOVE COOLER UNIT DRAIN HOSE GROMMET
|
|
| *A | for Driver Side | *B | for Passenger Side |
75.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
|
|
| *a | Bolt (A) | - | - |
|
Bolt |
|
Nut |
Using a universal socket wrench 12 mm, remove the 2 bolts (A).
Remove the 6 bolts and nut.
|
Remove in this Direction | - | - |
Remove the instrument panel reinforcement assembly with air conditioning unit assembly from the guide as shown in the illustration.
Detach the clamp and disconnect the connector.
Remove the instrument panel reinforcement assembly with air conditioning unit assembly from the vehicle.
76.REMOVE AIR CONDITIONER UNIT ASSEMBLY