Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455450 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -



b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the pulse according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
A-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH (w/ Reverse Shift-linked Mirror)


B452993E10
3.448,0.146 3.854,0.385 0.406,0.24 3.51,0.198 3.823,0.396 0.313,0.198 10 false E25

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-3 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E25-4 (CPUB) - Body ground Auxiliary battery power supply Always 11 to 14 V
E25-6 (BDR) - Body ground Auxiliary battery power supply Always 11 to 14 V
E25-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E25 front multiplex network door ECU LH connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-5 (BDRJ) - Body ground Power window regulator motor power supply Ignition switch off 11 to 14 V
E25-2 (PWE) - Body ground Power window regulator motor power supply Always Below 1 Ω
E25-9 (SGND) - Body ground Power window regulator motor power supply Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: for LHD

E25-11 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E25-12 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E25-13 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH (w/ Reverse Shift-linked Mirror)


B452993E09
3.448,0.146 3.854,0.385 0.406,0.24 3.563,0.188 3.875,0.385 0.313,0.198 10 false E7

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-3 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E7-4 (CPUB) - Body ground Auxiliary battery power supply Ignition switch ON 11 to 14 V
E7-6 (BDR) - Body ground Auxiliary battery power supply Ignition switch ON 11 to 14 V
E7-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E7 front multiplex network door ECU RH connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-5 (BDRJ) - Body ground Power window regulator motor power supply Ignition switch ON 11 to 14 V
E7-2 (PWE) - Body ground Power window regulator motor power supply Always Below 1 Ω
E7-9 (SGND) - Body ground Power window regulator motor power supply Always Below 1 Ω


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: for RHD

E7-11 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E7-12 (LIN2) - Body ground* LIN communication line Ignition switch ON Pulse generation
E7-13 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU LH (for RHD with Double Locking System)


B340249N15
4.073,0.188 4.521,0.469 0.448,0.281 4.177,0.26 4.49,0.458 0.313,0.198 10 false F16

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-1 (GND) - Body ground Ground Always Below 1 Ω
F16-4 (BDR) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-11 (CPUB) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-12 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


c.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F16-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU RH (for RHD with Double Locking System)


B340249N14
4.073,0.188 4.521,0.469 0.448,0.281 4.219,0.229 4.625,0.49 0.406,0.26 10 false F5

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-1 (GND) - Body ground Ground Always Below 1 Ω
F5-4 (BDR) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F5-11 (CPUB) - Body ground Auxiliary battery power supply Ignition switch ON 11 to 14 V
F5-12 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch off 11 to 14 V


c.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F5-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU LH (for LHD with Door Closer System)


B340249N15
4.073,0.188 4.521,0.469 0.448,0.281 4.177,0.26 4.49,0.458 0.313,0.198 10 false F16

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-1 (GND) - Body ground Ground Always Below 1 Ω
F16-4 (BDR) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-11 (CPUB) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F16-12 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


c.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F16-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR MULTIPLEX NETWORK DOOR ECU RH (for LHD with Door Closer System)


B340249N14
4.073,0.188 4.521,0.469 0.448,0.281 4.219,0.229 4.625,0.49 0.406,0.26 10 false F5

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-1 (GND) - Body ground Ground Always Below 1 Ω
F5-4 (BDR) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
F5-11 (CPUB) - Body ground Auxiliary battery power supply Ignition switch ON 11 to 14 V
F5-12 (SIG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch off 11 to 14 V


c.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-22 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
F5-23 (LIN3) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for LHD)


B290827E14
1.479,0.24 1.938,0.49 0.458,0.25 1.573,0.281 1.958,0.51 0.385,0.229 10 false E32

a.

Disconnect the E32 multiplex network master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E32-11 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
E32-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E32 multiplex network master switch assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E32-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E32-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for RHD)


B290827E15
1.479,0.24 1.938,0.49 0.458,0.25 1.573,0.281 1.958,0.51 0.385,0.229 10 false E14

a.

Disconnect the E14 multiplex network master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E14-11 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
E14-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the E32 multiplex network master switch assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E14-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
E14-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B464297E49
1.5,0.302 1.927,0.594 0.427,0.292 1.583,0.365 2.031,0.625 0.448,0.26 10 false E20

a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-1 (GND) - Body ground Ground Always Below 1 Ω
E20-2 (B) - Body ground Auxiliary battery power supply Always 11 to 14 V


c.

Reconnect the E20 front power window regulator motor assembly LH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E20-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


B464297E48
1.5,0.302 1.927,0.594 0.427,0.292 1.625,0.365 1.938,0.563 0.313,0.198 10 false E2

a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-1 (GND) - Body ground Ground Ignition switch off Below 1 Ω
E2-2 (B) - Body ground Auxiliary battery power supply Always 11 to 14 V


c.

Reconnect the E2 front power window regulator motor assembly RH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B464297E50
1.5,0.302 1.927,0.594 0.427,0.292 1.583,0.354 2.104,0.719 0.521,0.365 10 false F12

a.

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F12-1 (GND) - Body ground Ground Always Below 1 Ω
F12-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F12 rear power window regulator motor assembly LH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F12-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


B464297E51
1.5,0.302 1.927,0.594 0.427,0.292 1.615,0.354 2.135,0.719 0.521,0.365 10 false F1

a.

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F1-1 (GND) - Body ground Ground Always Below 1 Ω
F1-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F1 rear power window regulator motor assembly RH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
F1-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B427558E48
3.25,0.542 3.656,0.781 0.406,0.24 4.531,0.542 4.938,0.781 0.406,0.24 4.604,0.552 4.917,0.75 0.313,0.198 10 false D86 3.313,0.563 3.625,0.76 0.313,0.198 10 false G37

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D86-4 (+B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
D86-18 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D86-13 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY


B338712E09
1.458,0.365 1.844,0.583 0.385,0.219 1.531,0.396 1.885,0.552 0.354,0.156 10 false D24

a.

Disconnect the D24 steering lock actuator or upper bracket assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D24-1 (GND) - Body ground Ground Always Below 1 Ω
D24-6 (IG2) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
D24-7 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the D24 steering lock actuator or upper bracket assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D24-5 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B463711E05
3.24,0.24 3.677,0.49 0.438,0.25 3.333,0.281 3.792,0.479 0.458,0.198 10 false D73

a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D73-1 (+B) - Body ground Auxiliary battery power supply Always 11 to 14 V
D73-5 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D73 ID code box (immobiliser code ECU) connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D73-2 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (w/ Roof Sunshade System)


a.
B493581E20
1.563,0.208 1.927,0.448 0.365,0.24 1.667,0.25 1.979,0.479 0.313,0.229 10 false H4

Disconnect the H4 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H4-1 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
H4-2 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H4 sliding roof drive gear sub-assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H4-7 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation