This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch red indicator circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.
If a malfunction in the telematics system is detected, the manual (SOS) switch red If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157011 | Indicator (Red) Circuit Short to Ground | Manual (SOS) switch red indicator impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
| B157013 | Indicator (Red) Circuit Open | Manual (SOS) switch red indicator impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
If DTC B157011 or B157013 is stored, the manual (SOS) switch red indicator may not illuminate when another DTC is stored.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Clear the DTCs.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
| *a | Component without harness connected
(Map Light Assembly [Manual (SOS) Switch]) |
Remove the map light assembly (manual [SOS] switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from the batteries to terminal 6 (IND1) and a negative (-) lead to terminal 9 (GND3) of the map light assembly (manual [SOS] switch) connector.
Procedure1
Check if the manual (SOS) switch red indicator illuminates.
Manual (SOS) switch red indicator illuminates.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the D68 telematics transceiver connector.
Disconnect the H10 map light assembly (manual [SOS] switch) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D68,H10)Location & Routingewd_type=routing;type=c,c;code=D68,H10 Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiverewd_type=component;type=c;code=D68;pinno=4,3 Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H10;pinno=6,9 |
||
| D68-4 (IND1) - H10-6 (IND1) | Always | Below 1 Ω |
| D68-3 (SIG-) - H10-9 (GND3) | Always | Below 1 Ω |
| D68-4 (IND1) or H10-6 (IND1) - Body ground | Always | 10 kΩ or higher |
| D68-3 (SIG-) or H10-9 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>REGISTRATION