Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) C

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telematics transceiver detects an error in communication between the telematics transceiver and the airbag ECU assembly as a result of the telematics transceiver self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C464 Airbag Signal Signal Plausibility Failure Telematics transceiver detects an error in signals from airbag ECU assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Airbag ECU assembly

·

Telematics transceiver


Telematics B

WIRING DIAGRAM

E473254E02
2.531,1.125 2.833,1.302 0.302,0.177 10 false 23 1.958,1.125 2.479,1.323 0.521,0.198 10 false GSW3 4.896,1.125 5.406,1.313 0.51,0.188 10 false GSW 4.604,1.125 4.875,1.333 0.271,0.208 10 false 13 1.167,2.073 1.49,2.25 0.323,0.177 10 false D10 1.177,2.24 2.76,2.458 1.583,0.219 10 false Airbag ECU Assembly 4.677,2.063 5.229,2.292 0.552,0.229 10 false D68 4.667,2.229 6.771,2.438 2.104,0.208 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Check the DTC of "AIRBAG SYSTEM".

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK DTC

B

2.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

3.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)
3.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)

Pre-procedure1

a.
E422011C63
1.469,0.219 1.948,0.458 0.479,0.24 0.719,0.375 0.896,0.375 0.896,0.375 1.104,1.104 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.323,0.292 0.698,0.438 0.375,0.146 10 false GSW 1.594,0.26 2.031,0.51 0.438,0.25 10 false D68 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telematics Transceiver)


Remove the telematics transceiver with the connectors still connected.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Procedure1

a.

Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telematics transceiver while the airbag ECU assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection D68-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG




Post-procedure1

a.

None



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG ECU ASSEMBLY)
4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,D10)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D68-13 (GSW) - D10-23 (GSW3) Always Below 1 Ω
D68-13 (GSW) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR