This DTC is stored when the telematics transceiver detects an open or short circuit in the manual (SOS) switch.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C511 | Emergency Call Switch Circuit Short to Ground | Manual (SOS) switch impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
| B15C513 | Emergency Call Switch Circuit Open | Manual (SOS) switch impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Remove the map light assembly (manual [SOS] switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
| *a | Component without harness connected
(Map Light Assembly [Manual (SOS) Switch]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SIG1) - 9 (GND3) | Manual (SOS) switch not operated | 410 to 414 Ω |
| 13 (SIG1) - 9 (GND3) | Manual (SOS) switch operated | 81 to 83 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the D68 telematics transceiver connector.
Disconnect the H10 map light assembly (manual [SOS] switch) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D68,H10)Location & Routingewd_type=routing;type=c,c;code=D68,H10 Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiverewd_type=component;type=c;code=D68;pinno=21,3 Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H10;pinno=13,9 |
||
| D68-21 (SIG1) - H10-13 (SIG1) | Always | Below 1 Ω |
| D68-3 (SIG-) - H10-9 (GND3) | Always | Below 1 Ω |
| D68-21 (SIG1) - Body ground | Always | 10 kΩ or higher |
| D68-3 (SIG-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>REGISTRATION