Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) J

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E456575E07
2.323,2.281 2.677,2.458 0.354,0.177 10 false D68 2.333,2.458 4.281,2.865 1.948,0.406 10 false Telematics Transceiver 4.469,2.781 6.146,3.115 1.677,0.333 10 false Map Light Assembly 4.156,1.698 4.469,1.938 0.313,0.24 10 false 9 4.49,0.906 4.875,1.083 0.385,0.177 10 false RRID 1.281,1.021 3.188,1.302 1.906,0.281 10 false from IG2 P Relay 4.479,1.708 4.948,1.885 0.469,0.177 10 false GND3 4.99,2.198 6.438,2.375 1.448,0.177 10 false Manual (SOS) Switch 2.875,1.198 3.99,1.396 1.115,0.198 10 false IG2 P NO. 3 3.313,1.823 3.781,2 0.469,0.177 10 false SIG- 3.708,1.719 4.021,1.958 0.313,0.24 10 false 3 4.208,0.917 4.594,1.094 0.385,0.177 10 false 5 4.469,2.594 4.844,2.802 0.375,0.208 10 false H10

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION

·

Inspect the fuse for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY POWER SOURCE)
a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the H10 map light assembly (manual [SOS] switch) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-5 (RRID) - Body Ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,H10)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

D68-3 (SIG-) - H10-9 (GND3) Always Below 1 Ω
D68-3 (SIG-) or H10-9 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)
a.
E427070C19
1.833,0.979 2.021,0.25 2.021,0.25 2.146,0.25 true 1.042,1 0.917,0.302 0.917,0.302 0.74,0.302 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 0.323,0.219 0.844,0.438 0.521,0.219 10 false GND3 2.25,0.188 2.688,0.396 0.438,0.208 10 false RRID
*a Component without harness connected
(Map Light Assembly [Manual (SOS) Switch])


Remove the map light assembly (manual [SOS] switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Apply auxiliary battery voltage to the connector.

Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → 5 (RRID)
Auxiliary battery negative (-) → 9 (GND3)
Always Manual (SOS) switch illumination comes on


c.

Check if the manual (SOS) switch illumination comes on.

OK:

The manual (SOS) switch illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)

3.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT