Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449816 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

If the entry lock and wireless door lock operations cannot be performed, the door control receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B627615E01
4.323,9.031 7.135,9.25 2.813,0.219 10 false Certification ECU (Smart Key ECU Assembly) 0.292,9.01 3.375,9.458 3.083,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 1.021,7.906 2.667,8.385 1.646,0.479 10 false Door Control Receiver 0.615,3.531 2.927,4.021 2.313,0.49 10 false Roof Header Electrical Key Antenna 0.99,2.292 2.229,2.708 1.24,0.417 10 false from LUG-IG1 NO.2 Fuse 1.094,0.729 2.906,1.302 1.813,0.573 10 false to Each IG Relay 2.875,1.906 3.438,2.219 0.563,0.313 10 false AM2 0.938,1.167 2.698,1.552 1.76,0.385 10 false to Each ACC Relay 0.948,0.313 2.271,0.51 1.323,0.198 10 false from MPX-B D NO.1 Fuse 0.906,1.729 2.271,1.948 1.365,0.219 10 false from Auxiliary Battery 5.135,0.344 5.698,0.656 0.563,0.313 10 false CUTB 5.135,1.677 5.698,1.99 0.563,0.313 10 false +B 5.125,1.083 5.688,1.396 0.563,0.313 10 false ACCD 5.125,0.771 5.688,1.083 0.563,0.313 10 false IG1D 5.844,1.396 6.406,1.708 0.563,0.313 10 false +B 5.844,0.792 6.406,1.104 0.563,0.313 10 false +B 6.125,1.333 6.688,1.646 0.563,0.313 10 false IC 5.854,4.917 6.417,5.229 0.563,0.313 10 false 5V 5.906,5.552 6.469,5.865 0.563,0.313 10 false +B 5.875,6.208 6.438,6.521 0.563,0.313 10 false +B 5.865,6.875 6.427,7.188 0.563,0.313 10 false +B 5.125,7.094 5.688,7.406 0.563,0.313 10 false ASEL 5.135,6.479 5.698,6.792 0.563,0.313 10 false CSEL 5.125,5.813 5.688,6.125 0.563,0.313 10 false RDAM 5.146,5.188 5.708,5.5 0.563,0.313 10 false RCO 6.302,7.896 6.865,8.208 0.563,0.313 10 false E 4.781,0.333 5.063,0.563 0.281,0.229 10 false D86 4.823,0.135 5.031,0.333 0.208,0.198 10 false 15 4.833,0.563 5.052,0.76 0.219,0.198 10 false 17 4.823,0.979 5.021,1.198 0.198,0.219 10 false 16 4.854,1.563 4.99,1.76 0.135,0.198 10 false 4 4.76,5.281 5.042,5.479 0.281,0.198 10 false G37 4.813,5.083 5.375,5.396 0.563,0.313 10 false 18 4.813,5.698 5.375,6.01 0.563,0.313 10 false 19 4.823,6.375 5.385,6.688 0.563,0.313 10 false 20 4.823,7.021 5.063,7.25 0.24,0.229 10 false 21 6.51,7.906 6.813,8.115 0.302,0.208 10 false D86 6.542,7.698 7.104,8.01 0.563,0.313 10 false 18 0.604,3.354 1.167,3.667 0.563,0.313 10 false G117 2.448,7.219 2.74,7.417 0.292,0.198 10 false G49 2.438,6.573 2.75,6.802 0.313,0.229 10 false G49 2.448,5.281 2.74,5.5 0.292,0.219 10 false G49 2.438,4.729 2.76,4.948 0.323,0.219 10 false G49 2.406,4.229 2.792,4.438 0.385,0.208 10 false G116 2.021,3.01 2.583,3.323 0.563,0.313 10 false ANT 2.188,4.729 2.75,5.042 0.563,0.313 10 false IG 2.177,5.156 2.74,5.469 0.563,0.313 10 false +5 1.969,5.823 2.531,6.135 0.563,0.313 10 false DATA 1.979,6.49 2.542,6.802 0.563,0.313 10 false CSEL 1.979,7.146 2.542,7.458 0.563,0.313 10 false ASEL 1.063,7.583 1.625,7.896 0.563,0.313 10 false GND 2.438,2.906 3,3.219 0.563,0.313 10 false 1 2.521,4.031 2.656,4.208 0.135,0.177 10 false 1 2.5,4.552 2.635,4.74 0.135,0.188 10 false 1 2.531,5.708 2.688,5.906 0.156,0.198 10 false 2 2.542,6.385 2.729,6.583 0.188,0.198 10 false 6 2.51,7.042 2.698,7.229 0.188,0.188 10 false 11 0.75,7.375 0.979,7.563 0.229,0.188 10 false 12 0.563,9.469 2.25,9.667 1.688,0.198 10 false : CAN Communication Line 2.021,4.073 2.583,4.385 0.563,0.313 10 false ANT 4.781,0.76 5.063,0.99 0.281,0.229 10 false D86 4.781,1.177 5.063,1.406 0.281,0.229 10 false D86 4.781,1.76 5.063,1.99 0.281,0.229 10 false D86 4.781,5.906 5.063,6.104 0.281,0.198 10 false G37 4.781,6.583 5.063,6.781 0.281,0.198 10 false G37 4.771,7.219 5.052,7.417 0.281,0.198 10 false G37 0.688,7.583 0.958,7.781 0.271,0.198 10 false G49 0.365,7.375 0.594,7.563 0.229,0.188 10 false 12 0.281,7.583 0.625,7.771 0.344,0.188 10 false G157 2.521,4.417 2.708,4.594 0.188,0.177 10 false *1 2.5,4.927 2.688,5.104 0.188,0.177 10 false *1 2.552,5.104 2.729,5.292 0.177,0.188 10 false 8 2.479,5.49 2.667,5.667 0.188,0.177 10 false *1 2.49,6.115 2.677,6.292 0.188,0.177 10 false *1 2.49,6.792 2.677,6.969 0.188,0.177 10 false *1 2.469,7.427 2.656,7.604 0.188,0.177 10 false *1 2.771,4.229 3.156,4.438 0.385,0.208 10 false G158 2.885,4.031 3.021,4.208 0.135,0.177 10 false 1 2.781,5.281 3.167,5.49 0.385,0.208 10 false G157 2.771,5.896 3.156,6.104 0.385,0.208 10 false G157 2.771,6.583 3.156,6.792 0.385,0.208 10 false G157 2.771,7.229 3.156,7.438 0.385,0.208 10 false G157 2.896,4.417 3.083,4.594 0.188,0.177 10 false *2 2.896,5.104 3.073,5.292 0.177,0.188 10 false 8 2.438,5.896 2.74,6.125 0.302,0.229 10 false G49 2.927,5.708 3.083,5.906 0.156,0.198 10 false 2 2.896,6.375 3.083,6.573 0.188,0.198 10 false 6 2.875,7.021 3.063,7.208 0.188,0.188 10 false 11 0.729,7.781 0.917,7.958 0.188,0.177 10 false *1 2.865,5.49 3.052,5.667 0.188,0.177 10 false *2 2.865,6.115 3.052,6.292 0.188,0.177 10 false *2 2.854,6.792 3.042,6.969 0.188,0.177 10 false *2 2.854,7.438 3.042,7.615 0.188,0.177 10 false *2 0.365,7.771 0.552,7.948 0.188,0.177 10 false *2 2.583,9.469 3.854,9.656 1.271,0.188 10 false *1: w/ Panic Switch 4.333,9.469 5.688,9.656 1.354,0.188 10 false *2: w/o Panic Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

·

Door control receiver

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.




PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage.

Standard voltage:

11 to 14 V (ignition switch off)


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.SYSTEM CHECK

B

3.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Door Ajar Warning Buzzer Function A
w/o Door Ajar Warning Buzzer Function B



A

4.CHECK DOOR AJAR WARNING

B

5.CHECK POWER DOOR LOCK CONTROL SYSTEM
4.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.

HINT:

Be sure to check the following before performing the procedure.

·

Ignition switch is off.

·

All the doors is close.

·

The lock sensor is on or lock switch is pressed on the electrical key transmitter sub-assembly.

·

Electrical key transmitter sub-assembly is in the vehicle exterior detection area.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

5.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

GO TO LIGHTING SYSTEM (Proceed to Door Courtesy Switch Circuit)

5.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

6.CHECK KEY DIAGNOSTIC MODE

B

6.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
i.
for LHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for Driver Door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Driver Door), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
for LHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door (for driver side) (w/ Rear Door Entry):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly (for driver side), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
B581616C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door (for front passenger side) (w/ Rear Door Entry):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly (for front passenger side), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
B581609C01
0.646,1.146 2.667,0.406 2.667,0.406 3,0.406 false 2.073,1.167 2.656,0.417 false 3.042,0.333 3.271,0.583 0.229,0.25 10 false *a
*a Electrical Key Transmitter Sub-assembly Inspection Point

The illustrations shown are examples only.


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vi.
B581610C01
0.688,0.375 2.677,1.417 2.677,1.417 3.01,1.417 false 2.042,0.396 2.667,1.417 false 3.052,1.344 3.281,1.594 0.229,0.25 10 false *a
*a Electrical Key Transmitter Sub-assembly Inspection Point

The illustrations shown are examples only.


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vii.
B581612C01
1.365,1.677 2.667,0.333 2.667,0.333 3,0.333 false 1.958,1.292 2.667,0.333 false 3.052,0.271 3.281,0.521 0.229,0.25 10 false *a
*a Electrical Key Transmitter Sub-assembly Inspection Point

The illustrations shown are examples only.


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




viii.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Buzzer sounds.




Result:
Result Proceed to
Key diagnostic mode inspections fail for both channels A
Key diagnostic mode inspections succeed for both channels B
Key diagnostic mode inspection succeeds for only one of the channels C



A

7.CHECK WAVE ENVIRONMENT

B

19.PERFORM REGISTRATION

C

29.CHECK WAVE ENVIRONMENT
7.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally B



A

8.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the ignition switch, depressing the brake pedal and pressing the power switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

9.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

18.INSPECT TRANSMITTER BATTERY

C

REPLACE TRANSMITTER BATTERY

9.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

10.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

11.CHECK ENTRY LOCK OPERATION
10.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK ENTRY LOCK OPERATION
11.CHECK ENTRY LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the function operates normally.


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G49*1 or G157*2 door control receiver connector.

*1: w/ Panic Switch

*2: w/o Panic Switch



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G49)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G37-18 (RCO) - G49-8 (+5) Always Below 1 Ω
G37-19 (RDAM) - G49-2 (DATA) Always Below 1 Ω
G37-20 (CSEL) - G49-6 (CSEL) Always Below 1 Ω
G37-21 (ASEL) - G49-11 (ASEL) Always Below 1 Ω
G49-12 (GND) - Body ground Always Below 1 Ω
G37-18 (RCO) or G49-8 (+5) - Other terminals and body ground Always 10 kΩ or higher
G37-19 (RDAM) or G49-2 (DATA) - Other terminals and body ground Always 10 kΩ or higher
G37-20 (CSEL) or G49-6 (CSEL) - Other terminals and body ground Always 10 kΩ or higher
G37-21 (ASEL) or G49-11 (ASEL) - Other terminals and body ground Always 10 kΩ or higher

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G157)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G37-18 (RCO) - G157-8 (+5) Always Below 1 Ω
G37-19 (RDAM) - G157-2 (DATA) Always Below 1 Ω
G37-20 (CSEL) - G157-6 (CSEL) Always Below 1 Ω
G37-21 (ASEL) - G157-11 (ASEL) Always Below 1 Ω
G157-12 (GND) - Body ground Always Below 1 Ω
G37-18 (RCO) or G157-8 (+5) - Other terminals and body ground Always 10 kΩ or higher
G37-19 (RDAM) or G157-2 (DATA) - Other terminals and body ground Always 10 kΩ or higher
G37-20 (CSEL) or G157-6 (CSEL) - Other terminals and body ground Always 10 kΩ or higher
G37-21 (ASEL) or G157-11 (ASEL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

14.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

14.CHECK DOOR CONTROL RECEIVER
a.
B601018C02
0.906,0.167 1.323,0.438 0.417,0.271 1.948,0.156 2.365,0.427 0.417,0.271 0.688,1.771 0.917,1.771 0.917,1.771 1.292,1.292 true 0.99,0.188 1.323,0.385 0.333,0.198 10 false G49 0.698,0.75 0.896,0.938 0.198,0.188 10 false *a 0.375,1.677 0.729,1.875 0.354,0.198 10 false GND 1.979,0.198 2.375,0.396 0.396,0.198 10 false G157 0.688,0.219 0.906,0.417 0.219,0.198 10 false *A 1.698,0.198 1.917,0.396 0.219,0.198 10 false *B
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-12 (GND) - Body ground Always Below 1 Ω

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-12 (GND) - Body ground Always Below 1 Ω



b.
B601020C02
1.167,0.198 1.563,0.458 0.396,0.26 2.01,0.198 2.406,0.458 0.396,0.26 1.146,1.656 1.271,1.656 1.271,1.656 1.417,1.344 true 1.99,1.167 2.302,1.708 2.302,1.708 2.469,1.708 true 0.948,0.698 1.135,0.875 0.188,0.177 10 false *a 0.406,2.531 0.719,2.688 0.313,0.156 10 false *b 1,4.333 1.313,4.49 0.313,0.156 10 false *c 2.177,4.333 2.49,4.49 0.313,0.156 10 false *d 1.229,0.229 1.542,0.385 0.313,0.156 10 false G49 0.146,3.417 0.563,3.75 0.417,0.333 10 false GND 2.531,1.625 2.969,1.833 0.438,0.208 10 false DATA 0.823,1.583 1.167,1.771 0.344,0.188 10 false GND 2.042,0.229 2.427,0.406 0.385,0.177 10 false G157 0.875,0.219 1.094,0.396 0.219,0.177 10 false *A 1.802,0.219 2.021,0.396 0.219,0.177 10 false *B
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-2 (DATA) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)

w/o Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-2 (DATA) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B601021C03
1.021,0.135 1.438,0.427 0.417,0.292 1.813,0.135 2.229,0.427 0.417,0.292 0.76,1.365 0.979,1.365 0.979,1.365 1.281,1.021 true 0.792,1.604 1.01,1.604 1.01,1.604 1.271,1.219 true 0.865,1.813 1.052,1.813 1.052,1.813 1.417,1.229 true 1.99,0.948 2.24,0.51 2.24,0.51 2.417,0.51 true 1.104,0.177 1.417,0.375 0.313,0.198 10 false G49 0.771,0.677 0.99,0.875 0.219,0.198 10 false *a 0.375,1.271 0.76,1.448 0.385,0.177 10 false CSEL 0.5,1.74 0.885,1.917 0.385,0.177 10 false ASEL 0.479,1.51 0.813,1.688 0.333,0.177 10 false GND 2.458,0.406 3.271,0.771 0.813,0.365 10 false IG (*A) 0.781,0.177 1,0.375 0.219,0.198 10 false *A 1.615,0.156 1.833,0.354 0.219,0.198 10 false *B 1.854,0.167 2.24,0.354 0.385,0.188 10 false G157
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-1 (IG) - G49-12 (GND) Ignition switch to ON 10 to 16 V
G49-6 (CSEL) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation
G49-11 (ASEL) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly held and then luggage electrical key switch off → on


Below 1 V → 4.5 to 6 V

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-6 (CSEL) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation
G157-11 (ASEL) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly held and then luggage electrical key switch off → on


Below 1 V → 4.5 to 6 V



b.
B601022C02
1.198,0.104 1.604,0.333 0.406,0.229 1.938,0.104 2.344,0.333 0.406,0.229 1.146,1.667 1.292,1.667 1.292,1.667 1.396,1.26 true 1.948,1.25 2.135,1.719 2.135,1.719 2.302,1.719 true 0.885,0.677 1.073,0.865 0.188,0.188 10 false *a 0.323,2.354 0.635,2.51 0.313,0.156 10 false *b 0.875,4.094 1.188,4.25 0.313,0.156 10 false *c 2.042,4.094 2.354,4.25 0.313,0.156 10 false *d 1.271,0.135 1.583,0.292 0.313,0.156 10 false G49 0.146,3.219 0.573,3.427 0.427,0.208 10 false GND 0.833,1.594 1.198,1.781 0.365,0.188 10 false GND 2.354,1.615 2.573,1.813 0.219,0.198 10 false +5 1.01,0.135 1.229,0.323 0.219,0.188 10 false *A 1.76,0.115 1.979,0.302 0.219,0.188 10 false *B 1.979,0.115 2.354,0.302 0.375,0.188 10 false G157
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-8 (+5) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)

w/o Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-8 (+5) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

18.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

19.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.CHECK ENTRY LOCK OPERATION
20.CHECK ENTRY LOCK OPERATION
a.

After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

21.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

21.READ VALUE USING GTS (B CODE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status No Regd or Regd No Regd: B code not registered correctly
Regd: B code registered correctly
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code
50003 125 132

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

22.READ VALUE USING GTS (B CODE DIFFERENCE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

22.READ VALUE USING GTS (B CODE DIFFERENCE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code Difference B code mismatch No or Yes No: Communication normal
Yes: Communication malfunction
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code Difference
50003 125 131

Result:
Result Proceed to
"No" is displayed on the GTS A
"Yes" is displayed on the GTS B



A

23.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

23.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Read the Data List according to the display on the GTS.

B473193C17
4.469,0.521 4.823,0.719 0.354,0.198 4.635,2.302 4.281,1.271 true 3.885,2.292 4.198,1.281 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 4.531,0.521 4.844,0.719 0.313,0.198 10 false D86 4.646,2.354 5.083,2.563 0.438,0.208 10 false ACCD 3.677,2.333 4.073,2.521 0.396,0.188 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Ignition switch off
ACC ON: Ignition switch to ACC
IG ON: Ignition switch to ON
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-17 (IG1D) - Body ground Ignition switch off Below 1 V
Ignition switch to ACC Below 1 V
Ignition switch to ON 9 V or higher
D86-16 (ACCD) - Body ground Ignition switch off Below 1 V
Ignition switch to ACC 9 V or higher
Ignition switch to ON 9 V or higher




Result:
Proceed to
OK
NG



OK

24.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

24.READ VALUE USING GTS (ACC SW, IG SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch status OFF or ON OFF: Ignition switch off
ON: Ignition switch to ACC
"ON" is also displayed when the ignition switch is to ON.
IG SW Ignition switch status OFF or ON OFF: Ignition switch off
ON: Ignition switch to ON
"OFF" is also displayed when the ignition switch to ACC.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the certification ECU (smart key ECU assembly) misjudges for any reason that the ignition switch is to ON even though the ignition switch is off, the entry lock and unlock functions will be disabled.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the ignition switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the ignition switch is off B



A

25.CHECK HARNESS AND CONNECTOR (BODY GROUND, POWER SUPPLY)

B

TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

25.CHECK HARNESS AND CONNECTOR (BODY GROUND, POWER SUPPLY)
a.
B601830C01
1.448,2.427 1.865,2.677 0.417,0.25 0.938,4.344 1.167,3.802 false 2.406,4.354 2.115,3.677 false 0.531,2.479 0.844,2.635 0.313,0.156 10 false *a 1.531,2.469 1.844,2.625 0.313,0.156 10 false D86 0.896,4.365 1.281,4.604 0.385,0.24 10 false E 2.26,4.365 2.771,4.615 0.51,0.25 10 false CUTB
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-18 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-15 (CUTB) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

26.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK ENTRY LOCK OPERATION
a.

Disconnect and reconnect the certification ECU (smart key ECU assembly) connectors.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

27.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

27.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

28.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
28.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

29.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally 1 or more times. B



A

30.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

30.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

31.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

32.CHECK WAVE ENVIRONMENT
31.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

32.CHECK WAVE ENVIRONMENT
32.CHECK WAVE ENVIRONMENT
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally 1 or more times. B



A

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the G49*1 or G157*2 door control receiver connector.

*1: w/ Panic Switch

*2: w/o Panic Switch



b.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G49,G37)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

G49-6 (CSEL) - G37-20 (CSEL) Always Below 1 Ω
G49-6 (CSEL) or G37-20 (CSEL) - Other terminals and body ground Always 10 kΩ or higher

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G157,G37)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

G157-6 (CSEL) - G37-20 (CSEL) Always Below 1 Ω
G157-6 (CSEL) or G37-20 (CSEL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B601023C02
1,0.135 1.448,0.417 0.448,0.281 1.865,0.135 2.313,0.417 0.448,0.281 0.75,1.49 0.948,1.49 0.948,1.49 1.313,1.042 true 0.729,1.74 0.927,1.74 0.927,1.74 1.302,1.229 true 1.104,0.177 1.427,0.385 0.323,0.208 10 false G49 0.844,0.656 1.052,0.854 0.208,0.198 10 false *a 0.396,1.396 0.833,1.594 0.438,0.198 10 false CSEL 0.406,1.667 0.75,1.865 0.344,0.198 10 false GND 0.792,0.135 1,0.333 0.208,0.198 10 false *A 1.938,0.156 2.344,0.354 0.406,0.198 10 false G157 1.667,0.135 1.875,0.333 0.208,0.198 10 false *B
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-6 (CSEL) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation

w/o Panic Switch
Tester Connection Condition Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-6 (CSEL) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

36.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

36.CHECK DOOR CONTROL RECEIVER
a.

Enter key diagnostic mode and select the channel for which the buzzer did not sound.


b.
B601124C02
1.146,0.177 1.542,0.438 0.396,0.26 2.01,0.177 2.406,0.438 0.396,0.26 1.156,1.667 1.281,1.667 1.281,1.667 1.427,1.354 true 2.01,1.167 2.323,1.708 2.323,1.708 2.49,1.708 true 0.99,0.802 1.177,1 0.188,0.198 10 false *a 0.406,2.531 0.719,2.688 0.313,0.156 10 false *b 1,4.333 1.313,4.49 0.313,0.156 10 false *c 2.177,4.333 2.49,4.49 0.313,0.156 10 false *d 1.219,0.208 1.51,0.385 0.292,0.177 10 false G49 0.146,3.417 0.563,3.75 0.417,0.333 10 false GND 2.552,1.615 2.979,1.813 0.427,0.198 10 false DATA 0.844,1.573 1.177,1.75 0.333,0.177 10 false GND 0.927,0.198 1.125,0.396 0.198,0.198 10 false *A 1.802,0.167 2,0.365 0.198,0.198 10 false *B 2.042,0.208 2.427,0.406 0.385,0.198 10 false G157
*A w/ Panic Switch
*B w/o Panic Switch
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-2 (DATA) - G49-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)

w/o Panic Switch
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G157)Location & Routing

Click Connector(G157)Body>Floor Wire / No. 3 Floor Wire>Door Control Receiver

G157-2 (DATA) - G157-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)


HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).



Result:
Proceed to
OK
NG



OK

37.INSPECT WINDOW GLASS ANTENNA WIRE

NG

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

37.INSPECT WINDOW GLASS ANTENNA WIRE

OK

38.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - ROOF HEADER ELECTRICAL KEY ANTENNA)

NG

38.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - ROOF HEADER ELECTRICAL KEY ANTENNA)
a.

Disconnect the G116 door control receiver connector.


b.

Disconnect the G117 roof header electrical key antenna connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G116,G117)Location & Routing

Click Connector(G116)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

Click Connector(G117)Body>Floor Wire / No. 3 Floor Wire>Antenna Cord Sub-Assembly

G116-1(ANT) - G117-1(ANT) Always Below 1 Ω
G116-1(ANT) or G117-1(ANT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

39.REPLACE ROOF HEADER ELECTRICAL KEY ANTENNA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.REPLACE ROOF HEADER ELECTRICAL KEY ANTENNA
a.

Temporarily replace the roof header electrical key antenna with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Roof)>REMOVAL


Result:
Proceed to
NEXT



NEXT

40.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
40.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

41.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (ROOF HEADER ELECTRICAL KEY ANTENNA)

41.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

42.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
42.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)