High-range hydrogen pressure of the hydrogen tank assembly is regulated to medium-range pressure of 1000 to 1600 kPa(abs) (145 to 232 psi(abs)) by the hydrogen supply regulator assembly (high pressure regulator). The 3 fuel injector assemblies regulate this medium-range pressure hydrogen gas to an approximately atmospheric pressure plus 10 to 280 kPa(abs) (1.45 to 40.6 psi(abs)) before feeding it into the FC stack.
The FC control ECU determines the number of fuel injector assemblies (1 to 3) to operate in accordance with the FC stack load.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1D9A1C | Hydrogen Injector 1 Circuit Voltage Out of Range | All of the following conditions are met, and there is an open in the No. 1 fuel injector assembly circuit or a short to the GND circuit (DTC detection signal is ON) for more than 3 seconds.
·
Auxiliary battery voltage is between 10.5 to 15 V ·
No. 1 fuel injector assembly is not in operation (1 trip detection logic) All of the following conditions are met, and there is a short in the +B circuit of the No. 1 fuel injector assembly circuit (DTC detection signal is ON) for more than 3 seconds. ·
Auxiliary battery voltage is between 10.5 to 15 V ·
No. 1 fuel injector assembly is not in operation (1 trip detection logic) |
·
No. 1 fuel injector assembly ·
FC control ECU ·
FC-B relay ·
Wire harness or connector |
Master Warning: Comes on | FC | A |
| Vehicle Condition | FC shutdown
(ignition switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List (EV)
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List (EV)
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | ○ | ○ | ○ | ○ | ○ | - |
| DTC No. | Data List |
|---|---|
| P1D9A1C | - |
It is suspected that malfunctions, or open/short circuits have occurred in the No. 1 fuel injector assembly.
Inspect the fuses of circuits related to this system before performing the following procedure.
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON and wait for 3 seconds or more.
Pre-procedure1
Disconnect the FC control ECU connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A48,B1)Location & Routingewd_type=routing;type=c,c;code=A48,B1 Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECUewd_type=component;type=c;code=A48;pinno=2 Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECUewd_type=component;type=c;code=B1;pinno=104 |
||
| A48-2 (+BP3) - B1-104 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Reconnect the FC control ECU connector.
OK
NG
Pre-procedure1
Disconnect the FC control ECU connector.
Disconnect the No. 1 fuel injector assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B1,B7)Location & Routingewd_type=routing;type=c,c;code=B1,B7 Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECUewd_type=component;type=c;code=B1;pinno=46,86 Click Connector(B7)Engine Compartment>No. 2 Stack Wire>No. 1 Fuel Injector Assemblyewd_type=component;type=c;code=B7;pinno=1,2 |
||
| B1-46 (VHI1) - B7-1 (VHI1) | Always | Below 1 Ω |
| B1-86 (HIN1) - B7-2 (HIN1) | Always | Below 1 Ω |
| B1-46 (VHI1) or B7-1 (VHI1) - Body ground and other terminals | Always | 10 kΩ or higher |
| B1-86 (HIN1) or B7-2 (HIN1) - Body ground and other terminals | Always | 10 kΩ or higher |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECUewd_type=component;type=c;code=B1;pinno=46,86 |
||
| B1-46 (VHI1) or B1-86 (HIN1) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Reconnect the No. 1 fuel injector assembly connector.
Reconnect the FC control ECU connector.
OK
NG
OK
NG
Pre-procedure1
Disconnect the FC control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECUewd_type=component;type=c;code=B1;pinno=104 |
||
| B1-104 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the FC control ECU connector.
OK
NG
Pre-procedure1
Disconnect the FC control ECU connector.
Remove the FC-B relay from the No. 1 front compartment relay block.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A48)Location & Routingewd_type=routing;type=c;code=A48 Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECUewd_type=component;type=c;code=A48;pinno=2 |
||
| A48-2 (+BP3) - 5 (FC-B relay holder) | Always | Below 1 Ω |
| A48-2 (+BP3) or 5 (FC-B relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reinstall the FC-B relay.
Reconnect the FC control ECU connector.
OK
NG