Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E7E87  Lost Communication with Hybrid/EV Powertrain Control Module (SIL) Missing Message  


DESCRIPTION

The FC control ECU and EV control ECU send and receive signals via serial communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E7E87 Lost Communication with Hybrid/EV Powertrain Control Module (SIL) Missing Message All of the following conditions are met, and there is a communication stop from the EV control ECU to the FC control ECU for 1 second or more continuously.
·

+B voltage is not low

·

1 second or more after starting the FC control ECU

·

IGCT NO. 2 relay retain request is ON


(1 trip detection logic)
·

EV control ECU

·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

WIRING DIAGRAM

A492227E01
3.26,1.656 3.875,1.854 0.615,0.198 10 false 120Ω 3.26,2.792 3.875,2.99 0.615,0.198 10 false 120Ω 3.26,3.938 3.875,4.135 0.615,0.198 10 false 120Ω 3.26,5.052 3.875,5.25 0.615,0.198 10 false 120Ω 6.052,1.646 6.667,1.844 0.615,0.198 10 false 120Ω 6.052,2.781 6.667,2.979 0.615,0.198 10 false 120Ω 6.052,3.917 6.667,4.115 0.615,0.198 10 false 120Ω 6.052,5.063 6.667,5.26 0.615,0.198 10 false 120Ω 3.729,1.333 4.344,1.531 0.615,0.198 10 false FRQ+ 3.75,1.75 4.365,1.948 0.615,0.198 10 false FRQ- 3.719,2.208 4.156,2.448 0.438,0.24 10 false DRN7 3.729,2.49 4.344,2.688 0.615,0.198 10 false FCK+ 3.76,2.885 4.375,3.083 0.615,0.198 10 false FCK- 3.719,3.323 4.156,3.563 0.438,0.24 10 false DRN4 3.729,3.615 4.344,3.813 0.615,0.198 10 false FTH+ 3.75,4.031 4.365,4.229 0.615,0.198 10 false FTH- 3.719,4.469 4.156,4.708 0.438,0.24 10 false DRN6 3.729,4.75 4.344,4.948 0.615,0.198 10 false HTF+ 5.542,5.156 6.156,5.354 0.615,0.198 10 false HTF- 3.719,5.604 4.156,5.844 0.438,0.24 10 false DRN5 4.167,1.354 4.781,1.552 0.615,0.198 10 false 56 5.542,1.344 6.156,1.542 0.615,0.198 10 false FRQ+ 5.542,1.75 6.156,1.948 0.615,0.198 10 false FRQ- 2.667,6.167 3.052,6.365 0.385,0.198 10 false B1 4.167,1.75 4.781,1.948 0.615,0.198 10 false 57 4.177,2.125 4.792,2.323 0.615,0.198 10 false 58 4.177,2.479 4.792,2.677 0.615,0.198 10 false 47 4.167,2.896 4.781,3.094 0.615,0.198 10 false 48 4.167,3.26 4.781,3.458 0.615,0.198 10 false 49 4.167,3.615 4.802,3.813 0.635,0.198 10 false 53 4.177,4.021 4.813,4.219 0.635,0.198 10 false 54 4.177,4.385 4.542,4.583 0.365,0.198 10 false 55 4.167,4.75 4.802,4.948 0.635,0.198 10 false 50 4.167,5.177 4.802,5.365 0.635,0.188 10 false 51 4.167,5.51 4.802,5.698 0.635,0.188 10 false 52 2.667,6.313 4.052,6.531 1.385,0.219 10 false FC Control ECU 5.208,5.25 5.656,5.469 0.448,0.219 10 false A15 5.708,6.24 6.865,6.49 1.156,0.25 10 false EV Control ECU 5.542,2.479 6.156,2.677 0.615,0.198 10 false FCL+ 5.531,2.885 6.146,3.083 0.615,0.198 10 false FCL- 5.531,3.625 6.146,3.823 0.615,0.198 10 false FTH+ 5.531,4.031 6.146,4.229 0.615,0.198 10 false FTH- 5.542,4.75 6.156,4.948 0.615,0.198 10 false HTF+ 5.552,5.792 6.167,5.99 0.615,0.198 10 false E1 5.542,0.271 6.156,0.469 0.615,0.198 10 false MREL 3.729,5.167 4.344,5.365 0.615,0.198 10 false HTF- 5.208,5.781 5.615,5.969 0.406,0.188 10 false A17 4.698,0.25 5.083,0.458 0.385,0.208 10 false A8*1 5.208,0.073 5.823,0.271 0.615,0.198 10 false 21 5.281,5.604 5.896,5.802 0.615,0.198 10 false 4 5.198,4.844 5.646,5.104 0.448,0.26 10 false A15 5.219,4.115 5.635,4.354 0.417,0.24 10 false A15 5.198,3.708 5.615,3.938 0.417,0.229 10 false A15 5.208,2.979 5.625,3.208 0.417,0.229 10 false A15 5.208,1.844 5.74,2.115 0.531,0.271 10 false A15 5.198,1.427 5.604,1.625 0.406,0.198 10 false A15 5.198,2.573 5.625,2.76 0.427,0.188 10 false A15 5.229,1.26 5.844,1.458 0.615,0.198 10 false 18 5.229,1.656 5.844,1.854 0.615,0.198 10 false 19 5.229,2.385 5.844,2.583 0.615,0.198 10 false 16 5.24,2.802 5.854,3 0.615,0.198 10 false 17 5.281,3.531 5.896,3.729 0.615,0.198 10 false 5 5.281,3.938 5.896,4.135 0.615,0.198 10 false 6 5.26,4.677 5.875,4.875 0.615,0.198 10 false 14 5.25,5.073 5.865,5.271 0.615,0.198 10 false 15 2.146,2.354 2.76,2.552 0.615,0.198 10 false 43 2.156,2.688 2.771,2.885 0.615,0.198 10 false 83 2.094,5.323 2.708,5.521 0.615,0.198 10 false 104 2.094,5.677 2.708,5.875 0.615,0.198 10 false 105 1.365,2.958 2.219,3.188 0.854,0.229 10 false FC-B NO. 2 0.771,3.135 1.219,3.365 0.448,0.229 10 false FC-B 0.438,3.521 1.208,3.74 0.771,0.219 10 false FC-B NO. 1 0.438,4.073 1.333,4.281 0.896,0.208 10 false R/B-B NO. 1 0.448,4.625 1.396,4.865 0.948,0.24 10 false R/B FR 0.604,5.688 1.729,6 1.125,0.313 10 false Auxiliary Battery 0.208,1.969 1.135,2.188 0.927,0.219 10 false R/R RR# 2 0.656,1.01 1.583,1.229 0.927,0.219 10 false IGCT NO. 2 0.229,1.406 1.156,1.625 0.927,0.219 10 false IGCT NO. 2 2.427,5.458 3.042,5.656 0.615,0.198 10 false E1 2.417,5.802 3.031,6 0.615,0.198 10 false E2 2.406,2.458 3.021,2.656 0.615,0.198 10 false +B1 2.406,2.802 3.021,3 0.615,0.198 10 false +B2 4.74,2.313 5.01,2.5 0.271,0.188 10 false *3 4.729,3.438 4.99,3.615 0.26,0.177 10 false *3 4.74,4.583 5.021,4.76 0.281,0.177 10 false *3 4.729,5.719 5.01,5.927 0.281,0.208 10 false *3 1.229,4.781 2.344,4.99 1.115,0.208 10 false *3: Shield Ground 0.552,2.26 0.771,2.469 0.219,0.208 10 false 2 1.333,2.26 1.552,2.469 0.219,0.208 10 false 1 0.552,2.688 0.771,2.896 0.219,0.208 10 false 3 1.344,2.688 1.563,2.896 0.219,0.208 10 false 5 1.333,0.552 1.552,0.76 0.219,0.208 10 false 5 0.552,0.552 0.771,0.76 0.219,0.208 10 false 3 1.333,0.135 1.552,0.344 0.219,0.208 10 false 2 0.552,0.135 0.771,0.344 0.219,0.208 10 false 1 5.552,0.667 6.167,0.865 0.615,0.198 10 false +B1 5.26,0.5 5.875,0.698 0.615,0.198 10 false 1 5.188,0.656 5.583,0.833 0.396,0.177 10 false A17 1.667,0.833 2.594,1.052 0.927,0.219 10 false PM-IGCT 5.552,1.021 6.167,1.219 0.615,0.198 10 false +B2 4.708,1.031 5.146,1.26 0.438,0.229 10 false A8*1 5.24,0.854 5.854,1.052 0.615,0.198 10 false 7 5.094,0.26 5.719,0.458 0.625,0.198 10 false D15*2 5.094,1.021 5.719,1.198 0.625,0.177 10 false D15*2 4.76,0.063 5.375,0.26 0.615,0.198 10 false 21 4.781,0.833 5.396,1.031 0.615,0.198 10 false 7 1.281,3.896 2.458,4.094 1.177,0.198 10 false *1: for LHD 1.26,4.344 2.438,4.542 1.177,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 2 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-4 (E1) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.



OK

2.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A8)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
A8-7 (+B2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the EV control ECU connector.



OK

6.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - EV CONTROL ECU)

NG

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO. 2 RELAY)
4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO. 2 RELAY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Remove the IGCT NO. 2 relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A8)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-1 (+B1) - 5 (IGCT NO. 2 relay holder) Always Below 1 Ω
A8-7 (+B2) - 5 (IGCT NO. 2 relay holder) Always Below 1 Ω
A17-1 (+B1), A8-7 (+B2) or 5 (IGCT NO. 2 relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the IGCT NO. 2 relay.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
D15-7 (+B2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the EV control ECU connector.



OK

6.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - EV CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO. 2 RELAY)
6.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,A15)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

B1-56 (FRQ+) - A15-18 (FRQ+) Ignition switch off Below 1 Ω
B1-57 (FRQ-) - A15-19 (FRQ-) Ignition switch off Below 1 Ω
B1-47 (FCK+) - A15-16 (FCL+) Ignition switch off Below 1 Ω
B1-48 (FCK-) - A15-17 (FCL-) Ignition switch off Below 1 Ω
B1-53 (FTH+) - A15-5 (FTH+) Ignition switch off Below 1 Ω
B1-54 (FTH-) - A15-6 (FTH-) Ignition switch off Below 1 Ω
B1-50 (HTF+) - A15-14 (HTF+) Ignition switch off Below 1 Ω
B1-51 (HTF-) - A15-15 (HTF-) Ignition switch off Below 1 Ω
B1-56 (FRQ+) or A15-18 (FRQ+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-57 (FRQ-) or A15-19 (FRQ-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-47 (FCK+) or A15-16 (FCL+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-48 (FCK-) or A15-17 (FCL-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-53 (FTH+) or A15-5 (FTH+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-54 (FTH-) or A15-6 (FTH-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-50 (HTF+) or A15-14 (HTF+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
B1-51 (HTF-) or A15-15 (HTF-) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,A15)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

B1-56 (FRQ+) or A15-18 (FRQ+) - Body ground Ignition switch ON Below 1 V
B1-57 (FRQ-) or A15-19 (FRQ-) - Body ground Ignition switch ON Below 1 V
B1-47 (FCK+) or A15-16 (FCL+) - Body ground Ignition switch ON Below 1 V
B1-48 (FCK-) or A15-17 (FCL-) - Body ground Ignition switch ON Below 1 V
B1-53 (FTH+) or A15-5 (FTH+) - Body ground Ignition switch ON Below 1 V
B1-54 (FTH-) or A15-6 (FTH-) - Body ground Ignition switch ON Below 1 V
B1-50 (HTF+) or A15-14 (HTF+) - Body ground Ignition switch ON Below 1 V
B1-51 (HTF-) or A15-15 (HTF-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the EV control ECU connector.


c.

Reconnect the FC control ECU connector.



OK

7.CHECK EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK EV CONTROL ECU

Pre-procedure1

a.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A352214C08
1.958,0.292 2.448,0.594 0.49,0.302 0.344,2.26 1.615,1.396 true 0.813,2.271 1.729,1.427 true 1.448,2.281 1.885,1.406 true 1.927,2.26 2.021,1.385 true 1.5,0.667 1.854,1.198 true 1.542,0.406 2.063,1.167 true 2.427,2.281 2.125,1.385 true 2.854,2.313 2.229,1.385 true 0.156,0.188 0.469,0.385 0.313,0.198 10 false *a 2.083,0.365 2.542,0.563 0.458,0.198 10 false A15 0.115,2.271 0.573,2.469 0.458,0.198 10 false FRQ- 0.542,2.281 1,2.479 0.458,0.198 10 false FRQ+ 1.292,2.302 1.75,2.5 0.458,0.198 10 false FCL- 1.781,2.313 2.24,2.51 0.458,0.198 10 false FCL+ 1.104,0.313 1.563,0.51 0.458,0.198 10 false FTH+ 1.094,0.583 1.552,0.781 0.458,0.198 10 false FTH- 2.802,2.323 3.26,2.521 0.458,0.198 10 false HTF+ 2.333,2.323 2.792,2.521 0.458,0.198 10 false HTF-
*a Component without harness connected
(EV Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A15-18 (FRQ+) - A15-19 (FRQ-) Ignition switch off 80 to 170 Ω
A15-16 (FCL+) - A15-17 (FCL-) Ignition switch off 80 to 170 Ω
A15-5 (FTH+) - A15-6 (FTH-) Ignition switch off 80 to 170 Ω
A15-14 (HTF+) - A15-15 (HTF-) Ignition switch off 80 to 170 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.



OK

NG

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO. 2 RELAY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Remove the IGCT NO. 2 relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-1 (+B1) - 5 (IGCT NO. 2 relay holder) Always Below 1 Ω
D15-7 (+B2) - 5 (IGCT NO. 2 relay holder) Always Below 1 Ω
A17-1 (+B1), D15-7 (+B2) or 5 (IGCT NO. 2 relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the IGCT NO. 2 relay.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR