Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0490698 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH (front passenger side buckle switch).

DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1771 Passenger Side Buckle Switch Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the front passenger side buckle switch circuit.

·

Front passenger side buckle switch malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Front seat inner belt assembly RH (Front passenger side buckle switch)

·

Occupant detection ECU


Occupant Detection A

WIRING DIAGRAM

C240591E38
0.083,3.052 2.688,3.427 2.604,0.375 10 false Front Seat Inner Belt Assembly RH (Front Passenger Side Buckle Switch) 5.167,3.073 6.875,3.448 1.708,0.375 10 false Occupant Detection ECU 5.156,2.906 5.635,3.177 0.479,0.271 10 false L20 5.135,0.781 5.458,0.99 0.323,0.208 10 false 7 5.146,1.958 5.417,2.156 0.271,0.198 10 false 9 1.885,0.771 2.229,0.99 0.344,0.219 10 false 1 1.896,1.958 2.198,2.156 0.302,0.198 10 false 2 0.083,2.875 0.365,3.052 0.281,0.177 10 false L60

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

When RoB X2102 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


Procedure1

a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK FRONT SEAT WIRE RH

Pre-procedure1

a.
E470786C01
0.844,0.635 1.302,0.906 0.458,0.271 0.26,3.688 0.719,3.958 0.458,0.271 0.958,0.656 1.208,0.813 0.25,0.156 10 false L20 0.375,3.719 0.646,3.885 0.271,0.167 10 false L60 0.833,0.188 1.146,0.385 0.313,0.198 10 false *a 0.135,3.198 0.448,3.396 0.313,0.198 10 false *b 0.677,2.74 1.042,2.958 0.365,0.219 10 false *1 2.427,2.667 2.792,2.885 0.365,0.219 10 false *2 1.5,2.51 1.865,2.729 0.365,0.219 10 false *3 2.135,2.344 2.5,2.563 0.365,0.219 10 false A 1.854,2.344 2.219,2.563 0.365,0.219 10 false B 1.24,2.344 1.604,2.563 0.365,0.219 10 false C 0.958,2.333 1.323,2.552 0.365,0.219 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L20)Location & Routing

Click Connector(L20)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L20-7 - Body ground Ignition switch ON Below 1 V
L20-9 - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH

Pre-procedure1

a.
E470787C01
0.844,0.635 1.302,0.906 0.458,0.271 0.26,3.688 0.719,3.958 0.458,0.271 1.573,4.292 1.813,4.292 true 0.948,0.667 1.219,0.844 0.271,0.177 10 false L20 0.365,3.719 0.646,3.896 0.281,0.177 10 false L60 0.833,0.188 1.146,0.385 0.313,0.198 10 false *a 0.135,3.198 0.448,3.396 0.313,0.198 10 false *b 1.833,4.219 2.198,4.438 0.365,0.219 10 false *4 0.677,2.74 1.042,2.958 0.365,0.219 10 false *1 2.427,2.667 2.792,2.885 0.365,0.219 10 false *2 1.5,2.51 1.865,2.729 0.365,0.219 10 false *3 2.135,2.344 2.5,2.563 0.365,0.219 10 false A 1.854,2.344 2.219,2.563 0.365,0.219 10 false B 1.24,2.344 1.604,2.563 0.365,0.219 10 false C 0.958,2.333 1.323,2.552 0.365,0.219 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Using a service wire, connect terminals 1 and 2 of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L20)Location & Routing

Click Connector(L20)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L20-7 - L20-9 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector C.



OK

5.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH

Pre-procedure1

a.
E470786C01
0.844,0.635 1.302,0.906 0.458,0.271 0.26,3.688 0.719,3.958 0.458,0.271 0.958,0.656 1.208,0.813 0.25,0.156 10 false L20 0.375,3.719 0.646,3.885 0.271,0.167 10 false L60 0.833,0.188 1.146,0.385 0.313,0.198 10 false *a 0.135,3.198 0.448,3.396 0.313,0.198 10 false *b 0.677,2.74 1.042,2.958 0.365,0.219 10 false *1 2.427,2.667 2.792,2.885 0.365,0.219 10 false *2 1.5,2.51 1.865,2.729 0.365,0.219 10 false *3 2.135,2.344 2.5,2.563 0.365,0.219 10 false A 1.854,2.344 2.219,2.563 0.365,0.219 10 false B 1.24,2.344 1.604,2.563 0.365,0.219 10 false C 0.958,2.333 1.323,2.552 0.365,0.219 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


None


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L20)Location & Routing

Click Connector(L20)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Occupant Detection ECU

L20-7- L20-9 Always 1 MΩ or higher
L20-7 - Body ground Always 1 MΩ or higher
L20-9 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

6.CLEAR DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CLEAR DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 10 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394

Result:
Result Proceed to
B1771 is not output A
B1771 is output B


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.


Post-procedure1

a.

None



A

B

8.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
8.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the front seat inner belt assembly RH with a new one.

HINT:
·

Perform the following inspection using known good parts from another vehicle if possible.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

Result:
Proceed to
NEXT



NEXT

9.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
9.CHECK FRONT SEAT INNER BELT ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 10 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394

Result:
Result Proceed to
B1771 is not output A
B1771 is output B


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Restore the front seat inner belt assembly RH that was installed for testing to its original location.

HINT:

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSTALLATION




A

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)

B

10.REPLACE OCCUPANT DETECTION ECU
10.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the occupant detection ECU with a new one.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL



d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)