Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0490698 OCCUPANT CLASSIFICATION SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then displays the instrument panel passenger airbag assembly and front seat cushion airbag assembly RH condition (activated/not activated) using the passenger airbag ON/OFF indicator.

HINT:

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.


Front Passenger Seat Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
Vacant Off On Off
Adult*1 is seated On Off Off
Child*2 is seated On or Off*2 Off or On*2 Off
Child restraint system is installed Off On Off
Occupant classification system failure Off On On

*1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.

*2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.


CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

2.PERFORM ZERO POINT CALIBRATION

NG

2.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435
OK:

"Zero Point Calibration is complete." is displayed.



Result:
Proceed to
OK
NG



OK

END (NORMAL AFTER PERFORMING ZERO POINT CALIBRATION)

NG

3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
a.

Loosen the 4 installation bolts of the front seat assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION


b.

Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION


Result:
Proceed to
NEXT



NEXT

4.PERFORM ZERO POINT CALIBRATION
4.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435
OK:

"Zero Point Calibration is complete." is displayed.



Result:
Proceed to
OK
NG



OK

END (THE 4 INSTALLATION BOLTS WAS LOOSEN)

NG

5.READ VALUE USING GTS
5.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Occupant Detection > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Passenger Buckle SW Passenger side buckle switch NG, Set or Unset Set: Front passenger seat belt is fastened
Unset: Front passenger seat belt is not fastened
"NG" will be displayed immediately after the ignition switch is turned to ON.
Body Electrical > Occupant Detection > Data List
Tester Display
Passenger Buckle SW
50003 394 24
OK:

The GTS display changes correctly in accordance with the operation of the front passenger side buckle switch.



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTORS

NG

9.CHECK CONNECTORS
6.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect the connectors from the occupant detection ECU, front occupant classification sensor LH and rear occupant classification sensor LH.


d.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

7.REPLACE OCCUPANT DETECTION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE OCCUPANT DETECTION ECU
a.

Connect the connectors to the front occupant classification sensor LH and rear occupant classification sensor LH.


b.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

9.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


d.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Replace the front seat inner belt assembly RH with a new one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)