| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B005013 | Driver Seat Belt Sensor Circuit Open | One of the following conditions is met:
·
The airbag ECU assembly detects an open circuit signal in the driver seat belt sensor circuit for 0.5 seconds. ·
A front seat inner belt assembly LH malfunction. ·
An airbag ECU assembly malfunction. |
·
Harness or connector ·
Front seat inner belt assembly LH ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly LH.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the front seat inner belt assembly LH connector.
Procedure1
Check that the connectors (on the airbag ECU assembly side and front seat inner belt assembly LH side) are not damaged.
The terminals of the connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Using a service wire, connect terminals 30 (LBE+) and 24 (GNDL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G23)Location & Routingewd_type=routing;type=c;code=G23 Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=G23;pinno=2,1 |
||
| G23-2 (LBE+) - G23-1 (LBE-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Disconnect the service wire from connector B.
OK
NG
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH) |
Using a service wire, connect terminals 2 (LBE+) and 1 (LBE-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Connect the airbag ECU assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B005013 is output | A |
| B005011 is output | B |
| B005012 is output | C |
Post-procedure1
None
A
B
C