Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00B500  Driver Seat Track Position Restraints Sensor Circuit Undetermined Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00B500 Driver Seat Track Position Restraints Sensor Circuit Undetermined Failure When it is determined that the specified number of times or more is not achieved after the ignition switch is turned to ON
·

Wire harness

·

Front seat adjuster assembly LH (seat position airbag sensor)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

E459537E01
4.646,2.729 5.094,2.917 0.448,0.188 10 false G23 2.677,3.177 4.885,3.438 2.208,0.26 10 false Front Seat Inner Belt Assembly LH 4.719,2.49 4.917,2.771 0.198,0.281 10 false 3 2.531,0.99 2.656,1.156 0.125,0.167 10 false 2 4.708,1 4.833,1.188 0.125,0.188 10 false 4 2.563,2.469 2.688,2.615 0.125,0.146 10 false 1 5.375,1.156 5.573,1.313 0.198,0.156 10 false 27 5.698,1.229 6.198,1.438 0.5,0.208 10 false LSP+ 5.406,2.625 5.615,2.813 0.208,0.188 10 false 24 5.719,2.698 6.281,2.854 0.563,0.156 10 false GNDL 4.031,1.229 4.635,1.406 0.604,0.177 10 false LSP+ 4.125,2.688 4.646,2.844 0.521,0.156 10 false LSP- 5.385,3.802 5.698,3.969 0.313,0.167 10 false G43 5.396,3.979 6.865,4.229 1.469,0.25 10 false Airbag ECU Assembly 0.083,3.135 0.385,3.302 0.302,0.167 10 false L45 0.094,3.302 2.24,3.688 2.146,0.385 10 false Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) 4.646,1.24 5.094,1.427 0.448,0.188 10 false G23 2.49,1.25 2.938,1.438 0.448,0.188 10 false L59 2.49,2.74 2.938,2.927 0.448,0.188 10 false L59 2.094,2.646 2.219,2.792 0.125,0.146 10 false 1 2.083,1.146 2.208,1.313 0.125,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly LH (seat position airbag sensor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
E457301C01
0.385,1.083 0.698,1.24 0.313,0.156 10 false *1 2.552,1.542 2.865,1.698 0.313,0.156 10 false *2 1.219,0.781 1.531,0.938 0.313,0.156 10 false *3 1.854,0.792 2.167,0.948 0.313,0.156 10 false *4
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and front seat adjuster assembly LH (seat position airbag sensor) side) are not damaged.

OK:

The terminals of the connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR)

Pre-procedure1

a.

Remove the front seat adjuster assembly LH (seat position airbag sensor).

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



Procedure1

a.

Inspect the seat position sensor.

i.

Remove and reinsert the metal plate into the slit of the seat position sensor LH and measure the current value.

E441589C01
5.99,1.292 6.156,1.292 6.156,1.292 6.365,1.052 true 5.458,0.688 5.625,0.688 5.625,0.688 5.625,0.448 false 5.427,2.115 5.76,1.781 5.76,1.781 5.927,1.781 true 3.135,2.427 3.385,2.427 3.385,2.427 3.635,2.271 false 4.125,2.458 4.292,2.458 4.292,2.458 4.542,2.25 false 6.01,1.698 6.177,1.865 0.167,0.167 10 false *1 5.792,1.229 6.042,1.396 0.25,0.167 10 false *2 0.531,0.698 0.781,0.865 0.25,0.167 10 false *a 5.208,0.604 5.458,0.771 0.25,0.167 10 false *b 2.865,2.354 3.115,2.521 0.25,0.167 10 false *c 3.938,2.375 4.188,2.542 0.25,0.167 10 false *c
*1 Seat Position Sensor *2 Battery
*a Component without harness connected
(Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Tester
*c Metal plate - -


Standard Current:
Tester Connection Condition Specified Condition
Tester positive (+) - 2 - Tester negative (-) - Battery negative (-) Metal plate in slit 4.7 to 7.3 mA
Tester positive (+) - 2 - Tester negative (-) - Battery negative (-) Metal plate not in slit 11.4 to 17.9 mA




Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)
a.
E457303C02
0.844,0.75 1.25,1 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 1.021,1.833 1.208,2 0.188,0.167 10 false E 2.063,1.833 2.25,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 0.938,0.802 1.302,0.958 0.365,0.156 10 false L45 0.573,0.25 0.76,0.417 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.813,2.094 2.042,2.25 0.229,0.156 10 false *4 1.635,1.833 1.823,2 0.188,0.167 10 false C 1.469,1.844 1.656,2.01 0.188,0.167 10 false D
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L45)Location & Routing

Click Connector(L45)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Position Airbag Sensor

L45-2 L45-1 Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E457304C02
0.833,0.75 1.24,1 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 2.708,4.229 2.458,4.229 2.458,4.229 2.344,4.063 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.719,1.823 0.906,1.99 0.188,0.167 10 false F 1.01,1.833 1.198,2 0.188,0.167 10 false E 2.063,1.833 2.25,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 0.938,0.802 1.302,0.958 0.365,0.156 10 false L45 0.573,0.25 0.76,0.417 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.833,2.063 2.063,2.219 0.229,0.156 10 false *4 2.771,4.167 3,4.354 0.229,0.188 10 false *5 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.635,1.833 1.823,2 0.188,0.167 10 false C 1.479,1.833 1.667,2 0.188,0.167 10 false D
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*5 Service Wire
*a Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L45)Location & Routing

Click Connector(L45)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Position Airbag Sensor

L45-2 - L45-1 Always Below 1 Ω



Post-procedure1

Result:
Proceed to
OK
NG


a.

Disconnect the service wire from connector B.



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
a.
E457303C02
0.844,0.75 1.25,1 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 1.021,1.833 1.208,2 0.188,0.167 10 false E 2.063,1.833 2.25,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 0.938,0.802 1.302,0.958 0.365,0.156 10 false L45 0.573,0.25 0.76,0.417 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.813,2.094 2.042,2.25 0.229,0.156 10 false *4 1.635,1.833 1.823,2 0.188,0.167 10 false C 1.469,1.844 1.656,2.01 0.188,0.167 10 false D
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L45)Location & Routing

Click Connector(L45)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Position Airbag Sensor

L45-2 - Body ground Always 1 MΩ or higher
L45-1 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E457303C02
0.844,0.75 1.25,1 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 1.021,1.833 1.208,2 0.188,0.167 10 false E 2.063,1.833 2.25,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 0.938,0.802 1.302,0.958 0.365,0.156 10 false L45 0.573,0.25 0.76,0.417 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.813,2.094 2.042,2.25 0.229,0.156 10 false *4 1.635,1.833 1.823,2 0.188,0.167 10 false C 1.469,1.844 1.656,2.01 0.188,0.167 10 false D
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L45)Location & Routing

Click Connector(L45)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Position Airbag Sensor

L45-2 - Body ground Ignition switch ON Below 1 V
L45-1 - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.
E457307C01
0.5,1.542 0.813,1.74 0.313,0.198 10 false *1 2.625,1.844 2.938,2.042 0.313,0.198 10 false *2 1.219,1.229 1.531,1.427 0.313,0.198 10 false *3 1.792,1.219 2.104,1.417 0.313,0.198 10 false *4
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness


Reconnect the airbag ECU assembly connector.


b.

Reconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC
9.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B00B500 is not output A
B00B500 is output B


Post-procedure1

a.

None



A

B

10.CHECK CONNECTORS
10.CHECK CONNECTORS

Pre-procedure1

a.
E457302C01
0.458,1.115 0.771,1.271 0.313,0.156 10 false *1 2.719,1.5 3.031,1.656 0.313,0.156 10 false *2 1.208,0.813 1.521,0.969 0.313,0.156 10 false *3 1.875,0.813 2.188,0.969 0.313,0.156 10 false *4
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect the airbag ECU assembly connector.


d.

Disconnect the front seat adjuster assembly LH (seat position airbag sensor) connector.


Procedure1

a.

Check that the connectors (on the front seat inner belt assembly LH side and wire harness side) are not damaged.

OK:

The terminals of the connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)
a.
E457305C03
1.031,0.667 1.438,0.917 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 2.51,1.125 2.26,1.125 2.26,1.125 2.042,0.875 true 1.354,1.115 1.604,1.115 1.604,1.115 1.823,0.885 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 0.979,1.833 1.167,2 0.188,0.167 10 false E 2.115,1.833 2.302,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 1.125,0.719 1.49,0.875 0.365,0.156 10 false G23 0.792,0.104 0.979,0.271 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.823,2.073 2.052,2.229 0.229,0.156 10 false *4 1.677,1.833 1.865,2 0.188,0.167 10 false C 1.427,1.844 1.615,2.01 0.188,0.167 10 false D 1,1.01 1.469,1.25 0.469,0.24 10 false LSP- 2.563,1.01 3.031,1.25 0.469,0.24 10 false LSP+
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G23)Location & Routing

Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G23-4 (LSP+) - G23-3 (LSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E457306C02
1.021,0.646 1.427,0.896 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 2.708,4.229 2.458,4.229 2.458,4.229 2.344,4.063 true 2.49,1.25 2.24,1.25 2.24,1.25 2.021,0.906 true 1.354,1.25 1.604,1.25 1.604,1.25 1.823,0.885 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.729,1.823 0.917,1.99 0.188,0.167 10 false F 0.969,1.823 1.156,1.99 0.188,0.167 10 false E 2.115,1.833 2.302,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 1.115,0.688 1.479,0.844 0.365,0.156 10 false G23 0.771,0.104 0.958,0.271 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.833,2.052 2.063,2.208 0.229,0.156 10 false *4 2.771,4.167 3,4.354 0.229,0.188 10 false *5 1.229,2.042 1.458,2.198 0.229,0.156 10 false *3 1.688,1.823 1.875,1.99 0.188,0.167 10 false C 1.427,1.833 1.615,2 0.188,0.167 10 false D 2.542,1.146 3.01,1.385 0.469,0.24 10 false LSP+ 0.979,1.146 1.448,1.385 0.469,0.24 10 false LSP-
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*5 Service Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G23)Location & Routing

Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G23-4 (LSP+) - G23-3 (LSP-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
a.
E457305C03
1.031,0.667 1.438,0.917 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 2.51,1.125 2.26,1.125 2.26,1.125 2.042,0.875 true 1.354,1.115 1.604,1.115 1.604,1.115 1.823,0.885 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 0.979,1.833 1.167,2 0.188,0.167 10 false E 2.115,1.833 2.302,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 1.125,0.719 1.49,0.875 0.365,0.156 10 false G23 0.792,0.104 0.979,0.271 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.823,2.073 2.052,2.229 0.229,0.156 10 false *4 1.677,1.833 1.865,2 0.188,0.167 10 false C 1.427,1.844 1.615,2.01 0.188,0.167 10 false D 1,1.01 1.469,1.25 0.469,0.24 10 false LSP- 2.563,1.01 3.031,1.25 0.469,0.24 10 false LSP+
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G23)Location & Routing

Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G23-4 (LSP+) - Body ground Always 1 MΩ or higher
G23-3 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E457305C03
1.031,0.667 1.438,0.917 0.406,0.25 0.865,3.656 1.271,3.906 0.406,0.25 1.167,4.365 1.417,4.365 1.417,4.365 1.688,4 true 2.625,3.49 2.375,3.49 2.375,3.49 2.125,3.813 true 2.51,1.125 2.26,1.125 2.26,1.125 2.042,0.875 true 1.354,1.115 1.604,1.115 1.604,1.115 1.823,0.885 true 0.406,2.313 0.594,2.479 0.188,0.167 10 false *1 0.708,1.833 0.896,2 0.188,0.167 10 false F 0.979,1.833 1.167,2 0.188,0.167 10 false E 2.115,1.833 2.302,2 0.188,0.167 10 false B 2.375,1.823 2.563,1.99 0.188,0.167 10 false A 2.792,2.719 3.042,2.885 0.25,0.167 10 false *2 1.125,0.719 1.49,0.875 0.365,0.156 10 false G23 0.792,0.104 0.979,0.271 0.188,0.167 10 false *a 2.677,3.385 3.146,3.625 0.469,0.24 10 false GNDL 0.802,4.281 1.365,4.51 0.563,0.229 10 false LSP+ 0.948,3.698 1.271,3.896 0.323,0.198 10 false G43 0.542,3.042 0.729,3.208 0.188,0.167 10 false *b 1.229,2.063 1.458,2.219 0.229,0.156 10 false *3 1.823,2.073 2.052,2.229 0.229,0.156 10 false *4 1.677,1.833 1.865,2 0.188,0.167 10 false C 1.427,1.844 1.615,2.01 0.188,0.167 10 false D 1,1.01 1.469,1.25 0.469,0.24 10 false LSP- 2.563,1.01 3.031,1.25 0.469,0.24 10 false LSP+
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag ECU Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Wire Harness
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G23)Location & Routing

Click Connector(G23)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G23-4 (LSP+) - Body ground Ignition switch ON Below 1 V
G23-3 (LSP-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR