Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095304 INTERIOR PANELS / TRIM _0491383 REAR SUNSHADE SYSTEM U

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  TERMINALS OF ECU  


CHECK REAR WINDOW SHADE ASSEMBLY


a.
E271437N02
1.448,0.427 1.885,0.74 0.438,0.313 1.552,0.49 2.01,0.688 0.458,0.198 10 false G16

Disconnect the G16 rear window shade assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
G16-8 (B) - Body ground Auxiliary battery power supply Within 60 seconds after ignition switch turned off, or ignition switch turned to ON again after 60 seconds have elapsed from time ignition switch turned off 11 to 14 V
G16-7 (IG) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G16-1 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the G16 rear window shade assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
G16-4 (RSW) - Body ground Rear sunshade operation signal
·

Within 60 seconds after ignition switch turned off or ignition switch turned to ON again after 60 seconds have elapsed from time ignition switch turned off

·

Cooler control switch assembly (rear sunshade switch) pushed


Below 1 V
·

Within 60 seconds after ignition switch turned off, or ignition switch turned to ON again after 60 seconds have elapsed from time ignition switch turned off

·

cooler control switch assembly (rear sunshade switch) not pushed


11 to 14 V
G16-3 (REV) - Body ground Reverse position signal Start the hybrid control system, shift lever in not R 11 to 14 V
Start the hybrid control system, shift lever in R Below 1 V
G16-5 (SW) - Body ground Rear sunshade operation signal
·

Within 60 seconds after ignition switch turned off, or ignition switch turned to ON again after 60 seconds have elapsed from time ignition switch turned off

·

Multi-display assembly (rear sunshade switch) pushed


Below 1 V
·

Within 60 seconds after ignition switch turned off, or ignition switch turned to ON again after 60 seconds have elapsed from time ignition switch turned off

·

Multi-display assembly (rear sunshade switch) not pushed


11 to 14 V



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C13
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D12-6 (REV) - Body ground Reverse position signal Start the Hybrid control system, shift lever in not R 11 to 14 V
Start the Hybrid control system, shift lever in R Below 1 V