Home › Vehicle Exterior › DOOR / HATCH › DOOR CLOSER SYSTEM › from 2021.08
RM37H0E _59 Vehicle Exterior _095314 DOOR / HATCH _0491384 DOOR CLOSER SYSTEM J

DOOR / HATCH  DOOR CLOSER SYSTEM  Rear Door Closer LH does not Operate  


DESCRIPTION

The rear left side door closer controls the rear multiplex network door ECU LH, and operates the door closer motor based on the switch signals in the rear door with motor lock assembly LH.

WIRING DIAGRAM

E456437E03
0.531,0.49 1.917,0.74 1.385,0.25 10 false from Auxiliary Battery 0.521,1.292 1.906,1.51 1.385,0.219 10 false from Auxiliary Battery 3.854,1.177 4.313,1.375 0.458,0.198 10 false BDR 3.865,0.427 4.479,0.625 0.615,0.198 10 false CPUB 3.479,0.542 3.938,0.74 0.458,0.198 10 false F16 3.479,1.313 3.938,1.51 0.458,0.198 10 false F16 3.49,6.688 3.948,6.885 0.458,0.198 10 false F16 3.479,2.354 3.938,2.552 0.458,0.198 10 false F15 3.49,2.885 3.948,3.083 0.458,0.198 10 false F15 3.479,3.417 3.938,3.615 0.458,0.198 10 false F15 3.49,3.948 3.948,4.146 0.458,0.198 10 false F15 3.49,4.479 3.948,4.677 0.458,0.198 10 false F15 3.49,5.01 3.948,5.208 0.458,0.198 10 false F15 3.479,5.531 3.938,5.729 0.458,0.198 10 false F15 3.49,6.115 3.948,6.313 0.458,0.198 10 false F15 2.365,1.5 3.219,1.708 0.854,0.208 10 false DOOR R/L 1 2.271,0.719 3.281,0.948 1.01,0.229 10 false MPX-B D NO.1 2.875,2.229 3.031,2.427 0.156,0.198 10 false 1 3.563,1.104 3.719,1.302 0.156,0.198 10 false 4 4.719,0.354 5.625,0.75 0.906,0.396 10 false 5 V Power Source Circuit 2.406,2.229 3.021,2.427 0.615,0.198 10 false CLM+ 2.385,2.76 3,2.958 0.615,0.198 10 false CLM- 2.875,2.76 3.031,2.958 0.156,0.198 10 false 5 3.552,2.146 3.708,2.344 0.156,0.198 10 false 1 3.563,2.677 3.719,2.875 0.156,0.198 10 false 2 3.875,2.24 4.333,2.438 0.458,0.198 10 false A2+ 3.875,2.771 4.333,2.969 0.458,0.198 10 false A2- 6.323,3.323 6.781,3.521 0.458,0.198 10 false CPU 4.729,1.979 5.708,2.229 0.979,0.25 10 false Control Circuit 3.875,3.281 4.49,3.479 0.615,0.198 10 false STOP 3.865,3.813 4.479,4.01 0.615,0.198 10 false H/FU 3.885,4.344 4.5,4.542 0.615,0.198 10 false POLE 3.885,4.885 4.5,5.083 0.615,0.198 10 false INIT 3.885,5.417 4.5,5.615 0.615,0.198 10 false HNDL 3.885,5.99 4.5,6.188 0.615,0.198 10 false CPSE 3.885,6.563 4.5,6.76 0.615,0.198 10 false GND 4.25,7.26 6.635,7.479 2.385,0.219 10 false Rear Multiplex Network Door ECU LH 3.51,3.198 3.823,3.396 0.313,0.198 10 false 10 3.51,3.729 3.823,3.927 0.313,0.198 10 false 11 3.521,4.271 3.833,4.469 0.313,0.198 10 false 12 3.51,5.323 3.823,5.521 0.313,0.198 10 false 14 3.51,4.802 3.823,5 0.313,0.198 10 false 13 3.552,6.49 3.708,6.688 0.156,0.198 10 false 1 3.552,5.917 3.708,6.115 0.156,0.198 10 false 9 2.385,3.302 3,3.5 0.615,0.198 10 false STOP 2.438,3.833 3.052,4.031 0.615,0.198 10 false H/FU 2.385,4.354 3,4.552 0.615,0.198 10 false POLE 2.385,4.896 3,5.094 0.615,0.198 10 false DLSE 2.406,5.417 3.021,5.615 0.615,0.198 10 false CLP3 2.385,5.99 3,6.188 0.615,0.198 10 false CPSE 0.229,6.563 0.688,6.76 0.458,0.198 10 false F20 0.229,6.76 2.781,6.979 2.552,0.219 10 false Rear Door with Motor Lock Assembly LH 0.948,3.083 2.115,3.281 1.167,0.198 10 false Door Closer Motor 0.771,3.573 2.313,3.792 1.542,0.219 10 false Temporarily Stop Switch 0.823,4.104 2.25,4.323 1.427,0.219 10 false Half/Full Latch Switch 1.104,4.625 1.917,4.823 0.813,0.198 10 false Pawl Switch 0.813,5.156 2.302,5.385 1.49,0.229 10 false Former Position Switch 1.063,5.698 2.01,5.906 0.948,0.208 10 false Handle Switch 2.885,3.844 3.042,4.042 0.156,0.198 10 false 4 2.875,3.302 3.031,3.5 0.156,0.198 10 false 2 2.865,4.365 3.021,4.563 0.156,0.198 10 false 6 2.865,4.885 3.021,5.083 0.156,0.198 10 false 3 2.875,5.417 3.031,5.615 0.156,0.198 10 false 7 2.865,5.99 3.021,6.188 0.156,0.198 10 false 8 6.031,0.302 6.49,0.5 0.458,0.198 10 false 5 V 3.531,0.323 3.844,0.521 0.313,0.198 10 false 11

CAUTION / NOTICE / HINT

NOTICE:

Inspect fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Rear Left Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Pawl Switch Pawl switch signal ON or OFF ON: Pawl switch is ON
OFF: Pawl switch is OFF
-
Closer Position Switch Former position switch ON or OFF ON: Former position switch ON
OFF: Former position switch OFF
-
Half/Full-latch Switch Half/full latch switch signal ON or OFF ON: Half/full latch switch ON
OFF: Half/full latch switch OFF
-
Closer Stop Switch Temporarily stop switch signal ON or OFF ON: Temporarily stop switch signal ON
OFF: Temporarily stop switch signal OFF
-
Outside Handle Switch Handle switch signal ON or OFF ON: Handle switch ON
OFF: Handle switch OFF
-
Body Electrical > Rear Left Door > Data List
Tester Display
Pawl Switch
Closer Position Switch
Half/Full-latch Switch
Closer Stop Switch
Outside Handle Switch
50003 160 1,4,38,39,43
OK:

The switches do not switch ON/OFF according to the door open/close operation.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR DOOR WITH MOTOR LOCK ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY AND BODY GROUND)
a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F16)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F16-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(F16)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F16-4 (BDR) - Body ground Ignition switch off 11 to 14 V
F16-11 (CPUB) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR DOOR WITH MOTOR LOCK ASSEMBLY LH)

NG

REPLACE REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR DOOR WITH MOTOR LOCK ASSEMBLY LH)
a.

Disconnect the F15 rear multiplex network door ECU LH connector.


b.

Disconnect the F20 rear door with motor lock assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F15,F20)Location & Routing

Click Connector(F15)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

Click Connector(F20)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

F15-1 (A2+) - F20-1 (CLM+) Always Below 1 Ω
F15-2 (A2-) - F20-5 (CLM-) Always Below 1 Ω
F15-1 (A2+) or F20-1 (CLM+) - Body ground Always 10 kΩ or higher
F15-2 (A2-) or F20-5 (CLM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR DOOR WITH MOTOR LOCK ASSEMBLY LH)
a.

Disconnect the F15 rear multiplex network door ECU LH connector.


b.

Disconnect the F20 rear door with motor lock assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F15,F20)Location & Routing

Click Connector(F15)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

Click Connector(F20)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

F15-9 (CPSE) - F20-8 (CPSE) Always Below 1 Ω
F15-10 (STOP) - F20-2 (STOP) Always Below 1 Ω
F15-11 (H/FU) - F20-4 (H/FU) Always Below 1 Ω
F15-12 (POLE) - F20-6 (POLE) Always Below 1 Ω
F15-13 (INIT) - F20-3 (DLSE) Always Below 1 Ω
F15-14 (HNDL) - F20-7 (CLP3) Always Below 1 Ω
F15-9 (CPSE) or F20-8 (CPSE) - Body ground Always 10 kΩ or higher
F15-10 (STOP) or F20-2 (STOP) - Body ground Always 10 kΩ or higher
F15-11 (H/FU) or F20-4 (H/FU) - Body ground Always 10 kΩ or higher
F15-12 (POLE) or F20-6 (POLE) - Body ground Always 10 kΩ or higher
F15-13 (INIT) or F20-3 (DLSE) - Body ground Always 10 kΩ or higher
F15-14 (HNDL) or F20-7 (CLP3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR DOOR WITH MOTOR LOCK ASSEMBLY LH
a.

Temporarily replace the rear door with motor lock assembly LH with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


b.

Check the door closer functions normally.

Click hereVehicle Exterior>DOOR / HATCH>DOOR CLOSER SYSTEM>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

END (REAR DOOR WITH MOTOR LOCK ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH