| *A | w/ Double Locking System or w/ Easy Closer | - | - |
| *A | w/ Easy Closer | *B | w/o Easy Closer |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the rear door glass sub-assembly LH, move the rear door glass sub-assembly LH to the lowest position before disconnecting the auxiliary battery negative (-) terminal.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
68174A
6.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
68199
8.REMOVE REAR DOOR BELT REAR SEAL
89225
10.REMOVE MULTIPLEX NETWORK DOOR REAR ECU (w/ Double Locking System or w/ Easy Closer)
67646A
11.REMOVE REAR DOOR ARMREST SET BRACKET
67842E
12.REMOVE REAR DOOR SERVICE HOLE COVER
13.REMOVE HOLE PLUG
68152C
14.REMOVE REAR DOOR GLASS RUN
67408E
15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
69804
18.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
69060A
19.REMOVE REAR DOOR WITH MOTOR LOCK ASSEMBLY (w/o Easy Closer)
| *1 | Release Plate | - | - |
|
Remove in this Direction |
|
TORX Screw |
|
Connector | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 TORX screws.
Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
Do not damage to body by Rear door lock assembly LH.
69038A
20.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY (w/o Easy Closer)
|
Open | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the rear door lock cover sub-assembly LH.
Disengage the claw to remove the rear door lock cover sub-assembly LH.
69740E
21.REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/o Easy Closer)
|
Remove in this Direction | - | - |
69780E
22.REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE (w/o Easy Closer)
|
Remove in this Direction | - | - |
69060A
23.REMOVE REAR DOOR WITH MOTOR LOCK ASSEMBLY (w/ Easy Closer)
|
Bolt |
|
Connector |
Disconnect the connectors.
Remove the 3 bolts.
| *1 | Release Plate | - | - |
|
Remove in this Direction |
|
"TORX" Screw |
|
Connector | - | - |
Using a T30 "TORX" socket wrench, remove the 3 TORX screws.
Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
Do not damage to body by Rear door lock assembly LH.
69038A
24.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY (w/ Easy Closer)
|
Open | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the rear door lock cover sub-assembly LH.
Disengage the claw to remove the rear door lock cover sub-assembly LH.
69740E
25.REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/ Easy Closer)
|
Remove in this Direction | - | - |
69780E
26.REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE (w/ Easy Closer)
|
Remove in this Direction | - | - |
69318D
27.REMOVE DOOR LOCK WIRING HARNESS SEAL
|
|
When reusing the rear door lock with motor assembly: