Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15DB  Telematics Transceiver Disconnected  


DESCRIPTION

If the radio receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the ignition switch is turned to ON and the radio receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15DB Telematics Transceiver Disconnected Telematics transceiver disconnected
·

Harness or connector

·

Telematics transceiver

·

Radio receiver assembly

·

Navigation ECU


Navigation System A

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E423965E28
0.521,0.344 1.917,0.792 1.396,0.448 10 false from Battery 1.75,0.49 2.115,0.677 0.365,0.188 10 false DCM 1.573,1 2.396,1.167 0.823,0.167 10 false IG2 P NO.3 0.24,0.813 1.604,1.104 1.365,0.292 10 false from IG2 P Relay 2.365,0.344 2.74,0.521 0.375,0.177 10 false D68 2.792,0.333 3.052,0.51 0.26,0.177 10 false +B 2.479,0.167 2.677,0.344 0.198,0.177 10 false 1 2.771,0.802 3.146,0.979 0.375,0.177 10 false IG2 2.417,0.594 2.646,0.771 0.229,0.177 10 false 19 2.792,2.25 2.938,2.427 0.146,0.177 10 false E 2.438,2.052 2.698,2.292 0.26,0.24 10 false 20 0.75,3.208 2.604,3.5 1.854,0.292 10 false : USB Communication Line 2.573,3.24 5.26,3.573 2.688,0.333 10 false Telematics Transceiver 3.271,0.344 3.688,0.521 0.417,0.177 10 false USB+ 3.292,0.813 3.708,0.99 0.417,0.177 10 false USB- 3.26,1.313 3.677,1.49 0.417,0.177 10 false USBS 3.896,0.156 4.042,0.354 0.146,0.198 10 false 2 3.896,0.625 4.042,0.823 0.146,0.198 10 false 1 3.906,1.104 4.104,1.281 0.198,0.177 10 false 3 5.604,1.583 5.99,1.802 0.385,0.219 10 false D141 5.594,1.75 6.719,2.052 1.125,0.302 10 false Navigation ECU 5.719,0.354 6.135,0.531 0.417,0.177 10 false USB+ 5.719,0.833 6.135,1.01 0.417,0.177 10 false USB- 5.719,1.292 6.135,1.469 0.417,0.177 10 false USBS 5.521,0.219 5.667,0.417 0.146,0.198 10 false 1 5.51,0.698 5.656,0.896 0.146,0.198 10 false 2 5.521,1.198 5.667,1.396 0.146,0.198 10 false 3 3.25,2.385 3.667,2.563 0.417,0.177 10 false USBV 3.24,2.875 3.656,3.052 0.417,0.177 10 false USBG 3.844,2.188 4.115,2.417 0.271,0.229 10 false 15 3.875,2.656 4.094,2.865 0.219,0.208 10 false 31 5.438,3.313 7.156,3.583 1.719,0.271 10 false Radio Receiver Assembly 5.438,3.146 5.844,3.313 0.406,0.167 10 false D62 5.729,2.396 6.146,2.573 0.417,0.177 10 false USBV 5.729,2.854 6.146,3.031 0.417,0.177 10 false USBG 5.458,2.281 5.656,2.458 0.198,0.177 10 false 10 5.448,2.75 5.646,2.927 0.198,0.177 10 false 11 3.792,2.385 4.167,2.563 0.375,0.177 10 false D68 3.802,2.865 4.177,3.042 0.375,0.177 10 false D68 2.365,2.25 2.74,2.427 0.375,0.177 10 false D68 3.76,0.354 4.135,0.531 0.375,0.177 10 false D138 2.354,0.823 2.729,1 0.375,0.177 10 false D68 3.75,0.823 4.125,1 0.375,0.177 10 false D138 3.76,1.292 4.135,1.469 0.375,0.177 10 false D138

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

B

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-20 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-1 (+B) - Body ground Ignition switch off 11 to 14 V
D68-19 (IG2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

Pre-procedure1

a.

Disconnect the D62 radio receiver assembly connector.


b.

Disconnect the D68 telematics transceiver connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D62,D68)Location & Routing

Click Connector(D62)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D62-10 (USBV) - D68-15 (USBV) Always Below 1 Ω
D62-11 (USBG) - D68-31 (USBG) Always Below 1 Ω
D62-10 (USBV) - Body ground Always 10 kΩ or higher
D62-11 (USBG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK RADIO RECEIVER ASSEMBLY (USBV, USBG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK RADIO RECEIVER ASSEMBLY (USBV, USBG)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-31 (USBG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-15 (USBV) - D68-31 (USBG) Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)

Pre-procedure1

a.
E427222C14
1.479,0.302 1.927,0.583 0.448,0.281 1.458,2.563 1.906,2.844 0.448,0.281 2.5,0.698 2.313,0.698 2.313,0.698 1.833,1.396 true 1.583,3.406 1.292,2.969 1.292,2.969 1.156,2.969 true 2.208,2.969 2.083,2.969 2.083,2.969 1.813,3.396 true 2.156,4.031 2.01,4.031 2.01,4.031 1.76,3.573 true 1.563,1.417 1.271,0.688 1.271,0.688 1.01,0.688 true 1.26,2.073 1.375,2.073 1.375,2.073 1.604,1.615 true 1.115,0.156 1.427,0.354 0.313,0.198 10 false *a 1.094,2.448 1.406,2.646 0.313,0.198 10 false *b 1.542,0.365 2,0.563 0.458,0.198 10 false D138 1.531,2.625 1.99,2.823 0.458,0.198 10 false D141 0.635,0.604 1.25,0.802 0.615,0.198 10 false USB- 0.719,2.875 1.333,3.073 0.615,0.198 10 false USB+ 2.573,0.594 3.188,0.792 0.615,0.198 10 false USB+ 2.271,2.896 2.885,3.094 0.615,0.198 10 false USB- 2.219,3.969 2.833,4.167 0.615,0.198 10 false USBS 0.823,2 1.438,2.198 0.615,0.198 10 false USBS
*a Front view of wire harness connector
(to Telematics Transceiver)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the D138 telematics transceiver connector.


b.

Disconnect the D141 navigation ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D138,D141)Location & Routing

Click Connector(D138)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(D141)Instrument Panel>Instrument Panel Wire>Navigation ECU Assembly

D138-2 (USB+) - D141-1 (USB+) Always Below 1 Ω
D138-1 (USB-) - D141-2 (USB-) Always Below 1 Ω
D138-3 (USBS) - D141-3 (USBS) Always Below 1 Ω
D138-2 (USB+) - Body ground Always 10 kΩ or higher
D138-1 (USB-) - Body ground Always 10 kΩ or higher
D138-3 (USBS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TELEMATICS TRANSCEIVER

Pre-procedure1

a.

Replace the telematics transceiver with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

B

7.CHECK NAVIGATION ECU
7.CHECK NAVIGATION ECU

Pre-procedure1

a.

Replace the navigation ECU with a new one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (NAVIGATION ECU IS DEFECTIVE)

B

REPLACE RADIO RECEIVER ASSEMBLY