| *A | w/ Easy Closer | *B | w/o Easy Closer |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
| *A | w/ Double Locking System or w/ Easy Closer | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
69318D
1.INSTALL DOOR LOCK WIRING HARNESS SEAL
|
|
69780E
2.INSTALL REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE (w/ Easy Closer)
69740E
3.INSTALL REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/ Easy Closer)
69038A
4.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/ Easy Closer)
69060A
5.INSTALL REAR DOOR WITH MOTOR LOCK ASSEMBLY (w/ Easy Closer)
|
"TORX"Screw |
|
Connector |
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
Connect the rear door lock assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.
Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock assembly LH.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 "TORX" screws.
|
TORX Screw |
|
Connector |
Install the rear door lock assembly LH with the 3 bolts as shown in the illustration.
Connect the connectors.
69780E
6.INSTALL REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE (w/o Easy Closer)
69740E
7.INSTALL REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/o Easy Closer)
69038A
8.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/o Easy Closer)
69060A
9.INSTALL REAR DOOR WITH MOTOR LOCK ASSEMBLY (w/o Easy Closer)
|
TORX Screw |
|
Connector |
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
Connect the rear door lock assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.
Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock assembly LH.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 TORX screws.
Connect the connector.
69804
10.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
68124B
12.INSTALL REAR DOOR QUARTER WINDOW GLASS
67408E
13.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
68152C
14.INSTALL REAR DOOR GLASS RUN
15.INSTALL HOLE PLUG
67842E
16.INSTALL REAR DOOR SERVICE HOLE COVER
67646A
17.INSTALL REAR DOOR ARMREST SET BRACKET
89225
18.INSTALL MULTIPLEX NETWORK DOOR ECU REAR (w/ Double Locking System or w/ Easy Closer)
86160B
19.INSTALL REAR SPEAKER ASSEMBLY
68199
20.INSTALL REAR DOOR BELT REAR SEAL
68197A
21.INSTALL REAR DOOR BELT FRONT SEAL
68174A
22.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
67604
23.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
24.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
69284D
25.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
26.CONNECT CABLE TO NEGATIVE CONNECTOR AUXILIARY BATTERY TERMINAL
27. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
28. CHECK FOR SRS WARNING LIGHT
29. INITIALIZE POWER WINDOW SYSTEM
30. CHECK FOR POWER WINDOW OPERATION
31. CHECK FOR DOOR LOCK OPERATION