| *A | w/ Rear Door Sunshade | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *A | w/ Easy Closer | *B | w/o Easy Closer |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | w/ Double Locking System or w/ Easy Closer | - | - |
| *A | w/ Rear Door Sunshade | *B | w/o Rear Door Sunshade |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
67003C
4.INSTALL REAR DOOR PANEL CUSHION
65923E
5.INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)
67888F
6.INSTALL REAR DOOR NO. 2 WEATHERSTRIP
67896
7.INSTALL REAR DOOR NO. 3 WEATHERSTRIP
75740
9.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67874C
12.INSTALL REAR DOOR NO. 5 WEATHERSTRIP
|
Double-sided Tape | - | - |
Clean the surface of the rear door.
1. Remove any remaining double-sided tape from the rear door.
2. Wipe off any adhesive residue with cleaner.
3. Using a heat light, heat a new rear door No. 5 weatherstrip and the front door surface.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Part | Temperature |
|---|---|
| Rear door No.5 weatherstrip. | 20 to 30°C (68 to 86°F) |
Remove the peeling paper from the face of the rear door No.5 weatherstrip.
Attach the clips and install the rear door No.5 weatherstrip.
67872
13.INSTALL REAR DOOR WEATHERSTRIP
68640A
14.INSTALL REAR DOOR CHECK ASSEMBLY
|
Bolt |
|
Nut |
When reusing a bolt:
1. Clean the threads of the bolt.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Install the rear door check assembly with a bolt and 2 nuts.
69204A
15.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
69241G
16.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
69242G
17.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
69227L
18.INSTALL REAR DOOR OUTSIDE HANDLE COVER
69240
19.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
69318D
20.INSTALL DOOR LOCK WIRING HARNESS SEAL
69770E
21.INSTALL LOCK / UNLOCK KNOB REAR DOOR INSIDE LOCKING CABLE (w/ Easy Closer)
69730M
22.INSTALL OPEN LEVER REAR DOOR LOCK REMOTE CONTROL CABLE (w/ Easy Closer)
69038A
23.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/ Easy Closer)
69770E
25.INSTALL LOCK / UNLOCK KNOB REAR DOOR INSIDE LOCKING CABLE (w/o Easy Closer)
69730M
26.INSTALL OPEN LEVER REAR DOOR LOCK REMOTE CONTROL CABLE (w/o Easy Closer)
69038A
27.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/o Easy Closer)
69804
29.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
|
Bolt |
|
Connector |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the rear door window regulator assembly with the 4 bolts.
Connect the connector.
67674B
30.INSTALL REAR DOOR FRAME GARNISH
68104
31.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Connect the connectors and temporally install the front door trim board sub-assembly LH.
Connect the connector to the rear power window regulator switch.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch on.
Move the rear door glass sub-assembly so that the door glass installation position can be seen.
Turn the ignition switch off.
|
Install in this Direction | - | - |
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Do not damage the rear door glass sub-assembly LH.
Install the rear door glass sub-assembly to the rear door window regulator sub-assembly.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
Disconnect the connector from the rear pawer window regulator switch.
Disconnect the 2 connectors from the multiplex network door rear ECU.
68189
32.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
68124B
33.INSTALL REAR DOOR QUARTER WINDOW GLASS
67408E
34.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
68152C
35.INSTALL REAR DOOR GLASS RUN
36.INSTALL HOLE PLUG
67842E
37.INSTALL REAR DOOR SERVICE HOLE COVER
67646A
38.INSTALL REAR DOOR ARMREST SET BRACKET
89225
39.INSTALL MULTIPLEX NETWORK DOOR REAR ECU (w/ Double Locking System or w/ Easy Closer)
68199
41.INSTALL REAR DOOR BELT REAR SEAL
68197A
42.INSTALL REAR DOOR BELT FRONT SEAL
68174A
43.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
69206C
44.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
81080M
45.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY
65908D
46.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
81230
47.INSTALL COURTESY LIGHT ASSEMBLY
67604
48.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
49.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
69284D
50.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
51.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
52. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
53. INITIALIZE POWER WINDOW CONTROL SYSTEM
54.CHECK POWER WINDOW OPERATION
55.CHECK DOOR LOCK OPERATION