The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.
The IG terminal power source voltage is supplied by turning the IG1 relay to ON.
The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IG terminal and monitors the result.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
Ignition switch ON Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly LH ·
Harness or connector |
AFS | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
Ignition switch ON Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly RH ·
Harness or connector |
AFS (Sub) | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
Ignition switch ON Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly LH ·
Harness or connector |
HL AutoLeveling | A | w/o Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
Ignition switch ON Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly RH ·
Harness or connector |
HL AutoLeveling (Sub) | A | w/o Adaptive High Beam System |
Inspect the fuses for circuits related to this system before performing the following procedure.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B242E for AFS is output | A |
| Only B242E for AFS (Sub) is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | AFS | B242E | Open in IG Circuit |
| Headlight ECU sub-assembly RH | AFS (Sub) | B242E | Open in IG Circuit |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Disconnect the A96 headlight ECU sub-assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A96)Location & Routingewd_type=routing;type=c;code=A96 Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LHewd_type=component;type=c;code=A96;pinno=4 |
||
| A96-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A96 headlight ECU sub-assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A96)Location & Routingewd_type=routing;type=c;code=A96 |
||
| A96-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A97 headlight ECU sub-assembly RH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A97)Location & Routingewd_type=routing;type=c;code=A97 Click Connector(A97)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RHewd_type=component;type=c;code=A97;pinno=4 |
||
| A97-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A97 headlight ECU sub-assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A97)Location & Routingewd_type=routing;type=c;code=A97 |
||
| A97-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B242E for HL AutoLeveling is output | A |
| Only B242E for HL AutoLeveling (Sub) is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | HL AutoLeveling | B242E | Open in IG Circuit |
| Headlight ECU sub-assembly RH | HL AutoLeveling (Sub) | B242E | Open in IG Circuit |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING