Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  FC Air Compressor Resolver Circuit  


DESCRIPTION

The cause of this malfunction may be the FC air compressor motor resolver.

Check the FC air compressor motor resolver internal resistance and connection condition from the inverter to the resolver.

Related Parts Check
Area Inspection
Wire harness and connector between the inverter and FC air compressor motor resolver Check for short circuit between wire harness and +B side.
Resolver, wire harness, connector Check the internal resistance of resolver (including wire harness), body ground resistance, and connector connection condition.
Wire harness, connector Check for open or short circuit of the wire harness

SYSTEM DESCRIPTION

A resolver is a sensor that is used to detect the position of the magnetic poles of the rotor of a FC air compressor motor. Knowing the position of the poles is indispensable for ensuring precise control of the FC air compressor motor.

Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.

The MG ECU, which is built into the inverter with converter assembly, detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a revolution speed sensor.

The MG ECU monitors signals output from the FC air compressor motor resolver and detects malfunctions.

A221242E07
1.406,3.25 0.76,4.542 false 2.229,3.667 1.76,4.844 false 4.5,2.104 4.333,2.417 false 4.521,3.552 3.917,4.156 false 1.323,3.469 1.51,3.719 0.188,0.25 10 -S 1.729,2.188 1.917,2.438 0.188,0.25 10 -S 0.875,2.677 1.115,2.885 0.24,0.208 10 +S 2.156,3.052 2.417,3.25 0.26,0.198 10 +S 1.198,2.219 1.385,2.427 0.188,0.208 10 -C 1.813,3.458 2,3.667 0.188,0.208 10 -C 0.865,3.188 1.073,3.396 0.208,0.208 10 +C 2.135,2.552 2.344,2.76 0.208,0.208 10 +C 0.542,4.563 1.01,4.792 0.469,0.229 10 Rotor 1.323,4.875 2.302,5.115 0.979,0.24 10 Excitation Coil 6.01,0.313 6.99,0.552 0.979,0.24 10 Excitation Coil 5.969,2.031 7.125,2.271 1.156,0.24 10 Detection Coil S 5.969,3.5 7.083,3.74 1.115,0.24 10 Detection Coil C 4.542,2.01 5.646,2.26 1.104,0.25 10 Virtual Waveform 4.552,3.469 5.656,3.719 1.104,0.25 10 Virtual Waveform

WIRING DIAGRAM

for LHD:
A480858E02
4.354,2.76 4.729,2.99 0.375,0.229 3.146,2.781 3.521,3.01 0.375,0.229 0.25,2.365 0.563,2.563 0.313,0.198 10 false B24 4.427,2.792 4.74,2.99 0.313,0.198 10 false BA1 0.125,2.927 3.073,3.156 2.948,0.229 10 false FC Air Compressor with Motor Assembly 5.583,2.896 6.969,3.302 1.385,0.406 10 false Inverter with Converter Assembly 6.208,0.365 6.854,0.771 0.646,0.406 10 false Oscillation Circuit 5.646,0.385 6.281,0.667 0.635,0.281 10 false GRF 1.813,0.396 2.146,0.573 0.333,0.177 10 false GRF 5.646,0.698 6.281,0.979 0.635,0.281 10 false GRFG 1.708,0.729 2.146,0.927 0.438,0.198 10 false GRFG 5.656,1.135 6.292,1.417 0.635,0.281 10 false GSN 1.792,1.052 2.167,1.229 0.375,0.177 10 false GSN 1.708,1.385 2.156,1.583 0.448,0.198 10 false GSNG 5.635,1.49 6.271,1.771 0.635,0.281 10 false GSNG 5.646,1.802 6.281,2.083 0.635,0.281 10 false GCS 1.792,1.708 2.177,1.896 0.385,0.188 10 false GCS 1.698,2.021 2.177,2.219 0.479,0.198 10 false GCSG 5.646,2.115 6.281,2.396 0.635,0.281 10 false GCSG 5.656,2.385 6.292,2.667 0.635,0.281 10 false DRN6 0.26,2.531 3.208,2.76 2.948,0.229 10 false FC Air Compressor Motor Resolver 0.406,0.229 1.479,0.448 1.073,0.219 10 false Excitation Coil 5.417,0.396 5.625,0.594 0.208,0.198 10 false 20 5.448,0.729 5.604,0.906 0.156,0.177 10 false 9 5.406,1.063 5.625,1.25 0.219,0.188 10 false 18 5.417,1.719 5.646,1.875 0.229,0.156 10 false 17 5.458,1.385 5.635,1.542 0.177,0.156 10 false 7 5.458,2.042 5.677,2.229 0.219,0.188 10 false 6 5.448,2.313 5.719,2.469 0.271,0.156 10 false 8 4.792,0.417 5.021,0.615 0.229,0.198 10 false 38 4.792,0.74 4.979,0.906 0.188,0.167 10 false 39 4.771,1.052 5,1.229 0.229,0.177 10 false 40 4.781,1.385 4.979,1.563 0.198,0.177 10 false 61 4.771,1.719 4.958,1.885 0.188,0.167 10 false 62 4.771,2.042 4.948,2.229 0.177,0.188 10 false 63 3.594,0.406 3.813,0.604 0.219,0.198 10 false 10 2.167,0.396 2.385,0.583 0.219,0.188 10 false 1 3.604,0.729 3.844,0.917 0.24,0.188 10 false 11 2.167,0.74 2.333,0.885 0.167,0.146 10 false 5 3.594,1.063 3.823,1.271 0.229,0.208 10 false 12 2.167,1.063 2.438,1.219 0.271,0.156 10 false 2 2.917,1.385 3.167,1.563 0.25,0.177 10 false 18 2.167,1.375 2.438,1.531 0.271,0.156 10 false 6 3.594,1.708 3.865,1.865 0.271,0.156 10 false 19 2.167,1.719 2.365,1.865 0.198,0.146 10 false 3 2.927,2.031 3.208,2.177 0.281,0.146 10 false 20 2.177,2.021 2.375,2.177 0.198,0.156 10 false 7 5.583,2.74 6.042,2.958 0.458,0.219 10 false A19 4.094,2.052 4.271,2.24 0.177,0.188 10 false 63 4.083,1.719 4.271,1.885 0.188,0.167 10 false 62 4.104,1.385 4.302,1.563 0.198,0.177 10 false 61 4.094,1.063 4.323,1.24 0.229,0.177 10 false 40 4.104,0.729 4.292,0.896 0.188,0.167 10 false 39 4.104,0.406 4.354,0.594 0.25,0.188 10 false 38 3.219,2.823 3.531,3.021 0.313,0.198 10 false BB1 2.906,0.406 3.125,0.604 0.219,0.198 10 false 10 2.917,0.729 3.156,0.917 0.24,0.188 10 false 11 2.917,1.063 3.146,1.271 0.229,0.208 10 false 12 3.583,1.385 3.833,1.563 0.25,0.177 10 false 18 2.917,1.708 3.188,1.865 0.271,0.156 10 false 19 3.604,2.042 3.885,2.188 0.281,0.146 10 false 20 4.781,2.302 4.958,2.49 0.177,0.188 10 false 64 4.083,2.302 4.26,2.49 0.177,0.188 10 false 64 3.604,2.302 3.917,2.5 0.313,0.198 10 false 21 2.938,2.302 3.25,2.5 0.313,0.198 10 false 21 3.052,3.094 3.802,3.344 0.75,0.25 10 false Stack Wire

for RHD:
A480858E04
4.344,2.76 4.719,2.99 0.375,0.229 3.146,2.771 3.521,3 0.375,0.229 0.25,2.365 0.563,2.563 0.313,0.198 10 false B24 4.406,2.802 4.719,3 0.313,0.198 10 false BA1 0.125,2.927 3.073,3.156 2.948,0.229 10 false FC Air Compressor with Motor Assembly 5.635,2.948 7.052,3.438 1.417,0.49 10 false Inverter with Converter Assembly 6.208,0.365 6.854,0.771 0.646,0.406 10 false Oscillation Circuit 5.646,0.385 6.281,0.667 0.635,0.281 10 false GRF 1.813,0.396 2.146,0.573 0.333,0.177 10 false GRF 5.646,0.698 6.281,0.979 0.635,0.281 10 false GRFG 1.708,0.729 2.146,0.927 0.438,0.198 10 false GRFG 5.656,1.135 6.292,1.417 0.635,0.281 10 false GSN 1.792,1.052 2.167,1.229 0.375,0.177 10 false GSN 1.708,1.385 2.156,1.583 0.448,0.198 10 false GSNG 5.635,1.49 6.271,1.771 0.635,0.281 10 false GSNG 5.646,1.802 6.281,2.083 0.635,0.281 10 false GCS 1.792,1.708 2.177,1.896 0.385,0.188 10 false GCS 1.698,2.021 2.177,2.219 0.479,0.198 10 false GCSG 5.646,2.115 6.281,2.396 0.635,0.281 10 false GCSG 5.656,2.385 6.292,2.667 0.635,0.281 10 false DRN6 0.26,2.531 3.208,2.76 2.948,0.229 10 false FC Air Compressor Motor Resolver 0.406,0.229 1.479,0.448 1.073,0.219 10 false Excitation Coil 5.417,0.375 5.625,0.573 0.208,0.198 10 false 20 5.448,0.708 5.604,0.885 0.156,0.177 10 false 9 5.396,1.042 5.615,1.229 0.219,0.188 10 false 18 5.417,1.698 5.646,1.854 0.229,0.156 10 false 17 5.458,1.365 5.635,1.521 0.177,0.156 10 false 7 5.458,2.021 5.677,2.208 0.219,0.188 10 false 6 5.458,2.292 5.729,2.448 0.271,0.156 10 false 8 4.792,0.417 5.021,0.615 0.229,0.198 10 false 38 4.792,0.74 4.979,0.906 0.188,0.167 10 false 39 4.781,1.052 5.01,1.229 0.229,0.177 10 false 40 4.792,1.385 4.99,1.563 0.198,0.177 10 false 61 4.781,1.719 4.969,1.885 0.188,0.167 10 false 62 4.792,2.052 4.969,2.24 0.177,0.188 10 false 63 3.594,0.406 3.813,0.604 0.219,0.198 10 false 10 2.167,0.396 2.385,0.583 0.219,0.188 10 false 1 3.604,0.729 3.844,0.917 0.24,0.188 10 false 11 2.167,0.74 2.333,0.885 0.167,0.146 10 false 5 3.594,1.063 3.823,1.271 0.229,0.208 10 false 12 2.167,1.063 2.438,1.219 0.271,0.156 10 false 2 2.917,1.385 3.167,1.563 0.25,0.177 10 false 18 2.167,1.375 2.438,1.531 0.271,0.156 10 false 6 3.594,1.708 3.865,1.865 0.271,0.156 10 false 19 2.167,1.719 2.365,1.865 0.198,0.146 10 false 3 2.927,2.031 3.208,2.177 0.281,0.146 10 false 20 2.177,2.021 2.375,2.177 0.198,0.156 10 false 7 5.625,2.802 6.083,3.021 0.458,0.219 10 false A18 4.094,2.052 4.271,2.24 0.177,0.188 10 false 63 4.083,1.719 4.271,1.885 0.188,0.167 10 false 62 4.104,1.385 4.302,1.563 0.198,0.177 10 false 61 4.094,1.063 4.323,1.24 0.229,0.177 10 false 40 4.104,0.729 4.292,0.896 0.188,0.167 10 false 39 4.104,0.406 4.354,0.594 0.25,0.188 10 false 38 3.219,2.813 3.531,3.01 0.313,0.198 10 false BB1 2.906,0.406 3.125,0.604 0.219,0.198 10 false 10 2.917,0.729 3.156,0.917 0.24,0.188 10 false 11 2.917,1.063 3.146,1.271 0.229,0.208 10 false 12 3.583,1.385 3.833,1.563 0.25,0.177 10 false 18 2.917,1.708 3.188,1.865 0.271,0.156 10 false 19 3.604,2.042 3.885,2.188 0.281,0.146 10 false 20 4.792,2.302 4.969,2.49 0.177,0.188 10 false 64 4.083,2.302 4.26,2.49 0.177,0.188 10 false 64 3.604,2.302 3.917,2.5 0.313,0.198 10 false 21 2.938,2.302 3.25,2.5 0.313,0.198 10 false 21 3.042,3.073 3.854,3.375 0.813,0.302 10 false Stack Wire

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
C361311C89
0.063,1.052 0.479,1.396 0.417,0.344 0.063,0.625 0.479,0.969 0.417,0.344 1.74,1.021 1.646,0.438 true 1.896,1 2.427,0.5 true 1.896,1.104 2.417,1.865 true 1.625,1 1.031,0.521 true 1.656,1.073 1.125,1.802 true 1.74,1.083 1.833,1.813 true 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 2.375,1.885 2.833,2.083 0.458,0.198 10 false GRF 1.708,1.833 2.167,2.031 0.458,0.198 10 false GSN 0.958,1.823 1.417,2.021 0.458,0.198 10 false GCS 2.479,0.406 3.094,0.604 0.615,0.198 10 false GRFG 1.438,0.302 2.052,0.5 0.615,0.198 10 false GSNG 0.75,0.365 1.365,0.563 0.615,0.198 10 false GCSG 0.156,0.719 0.469,0.917 0.313,0.198 10 false A19 0.135,1.146 0.448,1.344 0.313,0.198 10 false A18 0.542,0.729 0.854,0.927 0.313,0.198 10 false *A 0.563,1.146 0.875,1.344 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) - Body ground Ignition switch ON Below 1 V
A19-9 (GRFG) - Body ground Ignition switch ON Below 1 V
A19-18 (GSN) - Body ground Ignition switch ON Below 1 V
A19-7 (GSNG) - Body ground Ignition switch ON Below 1 V
A19-17 (GCS) - Body ground Ignition switch ON Below 1 V
A19-6 (GCSG) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) - Body ground Ignition switch ON Below 1 V
A18-9 (GRFG) - Body ground Ignition switch ON Below 1 V
A18-18 (GSN) - Body ground Ignition switch ON Below 1 V
A18-7 (GSNG) - Body ground Ignition switch ON Below 1 V
A18-17 (GCS) - Body ground Ignition switch ON Below 1 V
A18-6 (GCSG) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

2.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FC AIR COMPRESSOR MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C361311C89
0.063,1.052 0.479,1.396 0.417,0.344 0.063,0.625 0.479,0.969 0.417,0.344 1.74,1.021 1.646,0.438 true 1.896,1 2.427,0.5 true 1.896,1.104 2.417,1.865 true 1.625,1 1.031,0.521 true 1.656,1.073 1.125,1.802 true 1.74,1.083 1.833,1.813 true 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 2.375,1.885 2.833,2.083 0.458,0.198 10 false GRF 1.708,1.833 2.167,2.031 0.458,0.198 10 false GSN 0.958,1.823 1.417,2.021 0.458,0.198 10 false GCS 2.479,0.406 3.094,0.604 0.615,0.198 10 false GRFG 1.438,0.302 2.052,0.5 0.615,0.198 10 false GSNG 0.75,0.365 1.365,0.563 0.615,0.198 10 false GCSG 0.156,0.719 0.469,0.917 0.313,0.198 10 false A19 0.135,1.146 0.448,1.344 0.313,0.198 10 false A18 0.542,0.729 0.854,0.927 0.313,0.198 10 false *A 0.563,1.146 0.875,1.344 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) - A19-9 (GRFG) Ignition switch off 6.5 to 21.5 Ω
A19-18 (GSN) - A19-7 (GSNG) Ignition switch off 10.0 to 37.5 Ω
A19-17 (GCS) - A19-6 (GCSG) Ignition switch off 9.0 to 35.5 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) - A18-9 (GRFG) Ignition switch off 6.5 to 21.5 Ω
A18-18 (GSN) - A18-7 (GSNG) Ignition switch off 10.0 to 37.5 Ω
A18-17 (GCS) - A18-6 (GCSG) Ignition switch off 9.0 to 35.5 Ω


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) or A19-9 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-18 (GSN) or A19-7 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-17 (GCS) or A19-6 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) or A18-9 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-18 (GSN) or A18-7 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-17 (GCS) or A18-6 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

FC AIR COMPRESSOR MOTOR RESOLVER CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A480856

Check the connection condition of the FC air compressor motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



Post-procedure1

a.

None.



A

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.
A480856

Disconnect the B24 FC air compressor motor resolver connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481334C03
3.531,1.667 3.969,2.021 0.438,0.354 0.802,1.448 1.24,1.813 0.438,0.365 3.531,1.24 3.969,1.594 0.438,0.354 1.313,0.917 1.75,1.51 true 1.99,0.917 1.854,1.51 true 1.406,2.156 1.76,1.667 true 1.917,2.177 1.885,1.688 true 2.448,2.177 2,1.656 true 2.5,0.833 2,1.521 true 5.156,1.438 4.792,0.729 true 5.469,0.719 5.219,1.427 true 6.073,0.688 5.354,1.438 true 5.906,2.281 5.354,1.51 true 5.344,2.25 5.219,1.49 true 5.156,1.5 4.74,2.281 true 2.563,0.75 3.021,0.948 0.458,0.198 10 false GCS 4.469,2.281 4.927,2.479 0.458,0.198 10 false GCS 2.458,2.198 2.917,2.396 0.458,0.198 10 false GCSG 4.573,0.594 5.031,0.792 0.458,0.198 10 false GCSG 1.74,2.198 2.198,2.396 0.458,0.198 10 false GSNG 5.469,0.583 5.927,0.781 0.458,0.198 10 false GSNG 2.01,0.76 2.469,0.958 0.458,0.198 10 false GSN 5.229,2.281 5.688,2.479 0.458,0.198 10 false GSN 5.917,2.281 6.375,2.479 0.458,0.198 10 false GRF 1.104,0.76 1.563,0.958 0.458,0.198 10 false GRF 1.063,2.198 1.521,2.396 0.458,0.198 10 false GRFG 6.135,0.583 6.594,0.781 0.458,0.198 10 false GRFG 3.604,1.323 4.063,1.521 0.458,0.198 10 false A19 0.927,1.563 1.385,1.76 0.458,0.198 10 false B24 0.823,0.292 1.281,0.49 0.458,0.198 10 false *a 4.135,0.281 4.594,0.479 0.458,0.198 10 false *b 4.031,1.323 4.344,1.521 0.313,0.198 10 false *A 3.625,1.76 4.083,1.958 0.458,0.198 10 false A18 4.052,1.729 4.365,1.927 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(FC Air Compressor Motor Resolver)
*b Front view of wire harness connector
(Inverter with Converter Assembly)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,B24)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

A19-20 (GRF) - B24-1 (GRF) Ignition switch off Below 1 Ω
A19-9 (GRFG) - B24-5 (GRFG) Ignition switch off Below 1 Ω
A19-18 (GSN) - B24-2 (GSN) Ignition switch off Below 1 Ω
A19-7 (GSNG) - B24-6 (GSNG) Ignition switch off Below 1 Ω
A19-17 (GCS) - B24-3 (GCS) Ignition switch off Below 1 Ω
A19-6 (GCSG) - B24-7 (GCSG) Ignition switch off Below 1 Ω
A19-20 (GRF) or B24-1 (GRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-9 (CRFG) or B24-5 (CRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-18 (GSN) or B24-2 (GSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-7 (GSNG) or B24-6 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-17 (GCS) or B24-3 (GCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-6 (GCSG) or B24-7 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,B24)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

A18-20 (GRF) - B24-1 (GRF) Ignition switch off Below 1 Ω
A18-9 (GRFG) - B24-5 (GRFG) Ignition switch off Below 1 Ω
A18-18 (GSN) - B24-2 (GSN) Ignition switch off Below 1 Ω
A18-7 (GSNG) - B24-6 (GSNG) Ignition switch off Below 1 Ω
A18-17 (GCS) - B24-3 (GCS) Ignition switch off Below 1 Ω
A18-6 (GCSG) - B24-7 (GCSG) Ignition switch off Below 1 Ω
A18-20 (GRF) or B24-1 (GRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-9 (CRFG) or B24-5 (CRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-18 (GSN) or B24-2 (GSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-7 (GSNG) or B24-6 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-17 (GCS) or B24-3 (GCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-6 (GCSG) or B24-7 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


HINT:

The FC air compressor motor resolver is not available as a supply part. If it requires replacement, replace the FC air compressor with motor assembly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor motor resolver connector.


b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR