Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  FC Air Compressor High-voltage Circuit  


DESCRIPTION

The cause of this malfunction may be the FC air compressor motor high-voltage circuit.

Check the FC air compressor motor internal resistance and the connection condition of the high-voltage line between the inverter and FC air compressor motor to check whether there is an open or short circuit.

Related Parts Check
Area Inspection
FC air compressor motor cable connection check Check for the connection condition of the cable from the inverter to the FC air compressor with motor.
FC Air Compressor or FC air compressor motor cable Check the FC air compressor with motor (including cable) internal resistance and the insulation resistance with body ground to check for an open or short circuit.

WIRING DIAGRAM

for LHD:
A484633E01
2.417,0.427 2.573,0.604 0.156,0.177 10 false W 2.427,0.75 2.583,0.927 0.156,0.177 10 false V 2.427,1.094 2.583,1.271 0.156,0.177 10 false U 2.667,1.073 2.823,1.25 0.156,0.177 10 false 1 1.115,1.594 1.354,1.771 0.24,0.177 10 false o1 1.104,1.76 3.771,2.042 2.667,0.281 10 false FC Air Compressor with Motor Assembly 1.146,2.406 2.479,2.594 1.333,0.188 10 false : High Voltage Line 4.896,0.385 5.156,0.563 0.26,0.177 10 false 3 4.885,1.083 5.104,1.26 0.219,0.177 10 false 1 4.896,0.74 5.156,0.917 0.26,0.177 10 false 2 5,1.74 7.125,1.948 2.125,0.208 10 false Inverter with Converter Assembly 2.656,0.365 2.813,0.542 0.156,0.177 10 false 3 2.656,0.729 2.813,0.906 0.156,0.177 10 false 2 4.979,1.573 5.823,1.771 0.844,0.198 10 false o3 5.104,0.531 5.26,0.708 0.156,0.177 10 false W 5.115,0.885 5.271,1.063 0.156,0.177 10 false V 5.115,1.219 5.271,1.396 0.156,0.177 10 false U

for RHD:
A484633E02
2.417,0.427 2.573,0.604 0.156,0.177 10 false W 2.427,0.75 2.583,0.927 0.156,0.177 10 false V 2.427,1.094 2.583,1.271 0.156,0.177 10 false U 2.667,1.073 2.823,1.25 0.156,0.177 10 false 1 1.115,1.594 1.354,1.771 0.24,0.177 10 false o1 1.104,1.76 3.771,2.042 2.667,0.281 10 false FC Air Compressor with Motor Assembly 1.146,2.406 2.479,2.594 1.333,0.188 10 false : High Voltage Line 4.896,0.385 5.156,0.563 0.26,0.177 10 false 1 4.885,1.083 5.104,1.26 0.219,0.177 10 false 3 4.896,0.74 5.156,0.917 0.26,0.177 10 false 2 5,1.74 7.125,1.948 2.125,0.208 10 false Inverter with Converter Assembly 2.656,0.365 2.813,0.542 0.156,0.177 10 false 3 2.656,0.729 2.813,0.906 0.156,0.177 10 false 2 4.979,1.573 5.823,1.771 0.844,0.198 10 false o2 5.104,0.531 5.26,0.708 0.156,0.177 10 false W 5.115,0.885 5.271,1.063 0.156,0.177 10 false V 5.115,1.219 5.271,1.396 0.156,0.177 10 false U

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter cover from the inverter with converter assembly.


c.
C371868C04
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Check that the bolts for the FC air compressor motor cable are tightened to the specified torque, the FC air compressor motor cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)


NOTICE:

Make sure that the tightening torque of the bolt is between 6.4 and 9.6 N*m (65 and 98 kgf*cm, 57 and 85 in.*lbf).



d.

Disconnect the FC air compressor motor cable from the inverter with converter assembly.


Procedure1

a.

Check for arc marks at the terminals for the FC air compressor motor cable.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Connect the FC air compressor motor cable to the inverter with converter assembly.


b.

Install the inverter cover.



A

2.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

2.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter cover from the inverter with converter assembly.


c.
C371868C04
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Disconnect the FC air compressor motor cable from the inverter with converter assembly.


Procedure1

a.
C371862C08
0.229,0.771 0.646,1.135 0.417,0.365 0.302,3.01 0.719,3.375 0.417,0.365 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.365,0.854 0.615,1.052 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable
(Inverter with Converter Assembly Side)


Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the FC air compressor motor temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-3 (W) - o3-1 (U) Ignition switch off 66.6 to 72.2 mΩ
o3-2 (V) - o3-3 (W) Ignition switch off 66.7 to 72.3 mΩ
o3-1 (U) - o3-2 (V) Ignition switch off 66.5 to 72.1 mΩ

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-1 (W) - o2-3 (U) Ignition switch off 66.6 to 72.2 mΩ
o2-2 (V) - o2-1 (W) Ignition switch off 66.7 to 72.3 mΩ
o2-3 (U) - o2-2 (V) Ignition switch off 66.5 to 72.1 mΩ


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C)



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-3 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o3-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o3-1 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o2-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o2-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air compressor motor cable.


b.

Install the inverter cover.



OK

FC AIR COMPRESSOR HIGH-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE CONNECTION CONDITION)
3.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the FC air compressor with motor assembly.

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL



c.
A480840

Check that the bolts for the FC air compressor motor cable are tightened to the specified torque, the FC air compressor motor cable is connected securely, and there are no contact problems.

Specified Condition:

T=10 N*m ( 102 kgf*cm, 7 ft.*lbf)



d.

Disconnect the FC air compressor motor cable from the FC air compressor with motor assembly.


Procedure1

a.

Check for arc marks at the terminals for the FC air compressor motor cable.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Connect the FC air compressor motor cable.


b.

Install the FC air compressor with motor assembly.



A

4.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

4.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371868C04
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Disconnect the FC air compressor motor cable from the inverter with converter assembly.


c.

Remove the FC air compressor with motor assembly.

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL



d.
A480840

Disconnect the FC air compressor motor cable from the FC air compressor with motor assembly.


Procedure1

a.
A489593C01
0.115,0.646 0.594,1.063 0.479,0.417 0.219,3.302 0.698,3.719 0.479,0.417 1.396,0.615 1.521,0.281 true 1.698,0.583 1.792,0.302 true 1.99,0.615 2.135,0.271 true 2.354,1.115 2.573,0.875 true 1.24,4.198 1.385,3.792 true 1.573,4.198 1.719,3.792 true 1.906,4.177 2.052,3.771 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.281,0.76 0.594,0.958 0.313,0.198 10 false o3 0.396,3.427 0.708,3.625 0.313,0.198 10 false o1 2.563,0.771 2.875,0.969 0.313,0.198 10 false *1 1.771,0.104 2.083,0.302 0.313,0.198 10 false V 1.49,0.104 1.802,0.302 0.313,0.198 10 false U 2.104,0.094 2.417,0.292 0.313,0.198 10 false W 1.167,4.229 1.479,4.427 0.313,0.198 10 false W 1.542,4.229 1.854,4.427 0.313,0.198 10 false V 1.865,4.24 2.177,4.438 0.313,0.198 10 false U 0.646,0.75 0.958,0.948 0.313,0.198 10 false *A
*A for LHD
*1 Shield Ground
*a FC Air Compressor Motor Cable


A481513C04
0.281,0.896 0.76,1.313 0.479,0.417 0.219,3.302 0.698,3.719 0.479,0.417 1.615,0.469 1.833,0.229 true 1.917,0.458 2.135,0.219 true 2.208,0.458 2.427,0.219 true 2.719,0.76 2.938,0.521 true 1.24,4.198 1.385,3.792 true 1.573,4.198 1.719,3.792 true 1.906,4.177 2.052,3.771 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.448,1.021 0.76,1.219 0.313,0.198 10 false o2 0.406,3.448 0.719,3.646 0.313,0.198 10 false o1 2.99,0.458 3.302,0.656 0.313,0.198 10 false *1 2.188,0.156 2.5,0.354 0.313,0.198 10 false V 2.49,0.156 2.802,0.354 0.313,0.198 10 false U 1.885,0.146 2.198,0.344 0.313,0.198 10 false W 1.167,4.229 1.479,4.427 0.313,0.198 10 false W 1.542,4.229 1.854,4.427 0.313,0.198 10 false V 1.865,4.24 2.177,4.438 0.313,0.198 10 false U 0.813,1.042 1.125,1.24 0.313,0.198 10 false *A
*A for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3,o1)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assembly

o3-3 (W) or o1-3 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o3-1 (U) or o1-1 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o3-2 (V) or o1-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2,o1)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assembly

o2-1 (W) or o1-3 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o2-3 (U) or o1-1 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
o2-2 (V) or o1-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher


NOTICE:

Wrap the terminal of the FC air compressor motor cable with insulating tape to prevent them from coming into contact with body ground.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3,o1)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assembly

o3-3 (W) - o1-3 (W) Ignition switch off Below 1 Ω
o3-1 (U) - o1-1 (U) Ignition switch off Below 1 Ω
o3-2 (V) - o1-2 (V) Ignition switch off Below 1 Ω
o3-3 (W) - o1-1 (V) Ignition switch off 10 MΩ or higher
o3-2 (V) - o1-1 (U) Ignition switch off 10 MΩ or higher
o3-1 (U) - o1-3 (W) Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2,o1)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assembly

o2-1 (W) - o1-3 (W) Ignition switch off Below 1 Ω
o2-3 (U) - o1-1 (U) Ignition switch off Below 1 Ω
o2-2 (V) - o1-2 (V) Ignition switch off Below 1 Ω
o2-1 (W) - o1-1 (V) Ignition switch off 10 MΩ or higher
o2-2 (V) - o1-1 (U) Ignition switch off 10 MΩ or higher
o2-3 (U) - o1-3 (W) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the FC air compressor motor cable.


b.

Install the inverter with converter assembly.



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY