Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2177/77    Initialization not Completed

for Preparation Click here


DESCRIPTION

Initialization is necessary if one of the following occurs: 1) the ECU is replaced; 2) a tire pressure warning valve and transmitter is replaced; 3) tires with a different tire pressure are installed; 4) the tires are rotated; or 5) a new vehicle is delivered.

DTC Code
DTC Detection Condition
Trouble Area
C2177/77
When all conditions below are met:
  1. During initialization
  2. Tire pressure warning valve and transmitter is not in stop mode
  3. Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more
  4. Vehicle speed is more than 8 km/h (5 mph) for a total of 20 minutes
  1. Tire pressure warning valve and transmitter
  2. Tire pressure warning antenna and receiver
  3. Tire pressure warning ECU
  4. Harness or connector

WIRING DIAGRAM


C171587E03


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or valve and transmitter have been replaced.

1.CHECK FREQUENCY RECEIVING CONDITION
  1. Check if the vehicle is located in an area such as the one described below:

    1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

      HINT:
      If the vehicle is located in an area such as described above, the tire pressure warning light may turn on only in a particular location.

    2. Devices using similar radio frequencies are used in the vehicle.

      OK:
      Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

      HINT:
      Radio frequency may be interrupted due to vehicle surroundings or devices installed by the user.



NG
CHECK IF ANY DEVICE IS INSTALLED BY USER
OK


2.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. *: It may take about 2 or 3 minutes until the values are displayed.
    2. If no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Condition
    proceed to
    Tire pressure values are not displayed
    A
    All tire pressure readings are equal to specified values
    B



B
END
A

GO TO C2121/21 to C2124/24 FLOWCHART (Click here)