Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    01-DF    Master Error

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
01-DF*
When either condition below is met:
  1. Device with a display fails and master is switched to the audio device.
  2. Communication error between sub-master (radio receiver) and master occurs.
  1. Multi-display power source circuit
  1. AVC-LAN circuit between multi-display and component which has stored this code
  1. AVC-LAN circuit between multi-display and radio receiver
  1. Multi-display
  1. Component which has stored this code

HINT:
*: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the power switch ON (ACC or IG), this code is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The multi-display is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read DESCRIPTION before performing the following procedures.

1.CHECK MULTI-DISPLAY POWER SOURCE CIRCUIT
  1. Refer to the multi-display power source circuit (Click here).
    If the power source circuit is operating normally, proceed to the next step.


NEXT


2.INSPECT RADIO RECEIVER


    E126486E01
  1. Disconnect the R5 and R6 receiver connectors.

  1. Measure the resistance of the receiver.

Standard resistance:
Tester Connection
Specified Condition
R5-9 (TX+) - R5-10 (TX-)
60 to 80 Ω
R6-5 (TX+) - R6-15 (TX-)
60 to 80 Ω



NG
REPLACE RADIO RECEIVER ASSEMBLY
OK


3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


    E126492E01
  1. Enter the diagnostic mode.

  1. Press the "LAN Mon" switch to change to "LAN Monitor" mode.

  1. Identify the component which has stored this code.
    Component table: 
    Display
    Component
    AUDIO H/U
    Radio receiver
    DSP-AMP
    Stereo component amplifier
    G/W
    Gateway ECU
    NAVI
    Navigation ECU

    HINT:
    "NAVI" is the component which has stored this code in the example shown in the illustration.


NEXT


4.CHECK WIRE HARNESS (MULTI-DISPLAY - COMPONENT WHICH HAS STORED THIS CODE)

HINT:
For details of the connectors, refer to "TERMINALS OF ECU" (Click here).



  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the multi-display and the component which has stored this code.

    1. Disconnect all connectors between the multi-display and the component which has stored this code.



    2. Check for an open or short in the AVC-LAN circuit between the multi-display and the component which has stored this code.

      OK:
      There is no open or short circuit.


      E126411E03



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (MULTI-DISPLAY - RADIO RECEIVER)

HINT:
For details of the connectors, refer to "TERMINALS OF ECU" (Click here).



  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the multi-display and the radio receiver.

    1. Disconnect all connectors between the multi-display and the radio receiver.



    2. Check for an open or short in the AVC-LAN circuit between the multi-display and the radio receiver.

      OK:
      There is no open or short circuit.


      E127893E03



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.REPLACE MULTI-DISPLAY
  1. Replace the multi-display with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END