Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and the occupant classification system.
When the center airbag sensor receives signals from the occupant classification ECU, it determines whether or not the front passenger airbag, front seat side airbag RH and seat belt pretensioner RH should be operated.
DTC B1650/32 is set when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detection Conditions
Trouble Areas
B1650/32
When one of following conditions is met:
  1. Occupant classification system malfunction
  2. Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal from occupant classification system circuit for 2 seconds
  3. Center airbag sensor malfunction
  1. Floor wire No. 2
  2. Occupant classification system
  3. Center airbag sensor

WIRING DIAGRAM


C123527E09


INSPECTION PROCEDURE

1.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the power switch ON (IG), and wait for at least 10 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



OK
GO TO DTC CHART
NG


2.CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)


    H100887E06
  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

    HINT:
    DTCs other than DTC B1650/32 may be output at this time, but they are not related to this check.



NG
USE SIMULATION METHOD TO CHECK
OK


3.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

    OK:
    Connectors are connected.



NG
CONNECT CONNECTOR
OK


4.CHECK FLOOR WIRE NO. 2 (OPEN)
C130791E02
  1. Disconnect the connectors from the center airbag sensor and the occupant classification ECU.

  1. Using a service wire, connect terminals O4-8 (FSR+) and O4-4 (FSR-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A19-16 (FSP+) - A19-24 (FSP-)
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT)
C130792E02
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A19-16 (FSP+) - A19-24 (FSP-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (TO B+)
C130792E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Terminal Connection
    Specified Condition
    A19-16 (FSP+) - Body ground
    Below 1 V
    A19-24 (FSP-) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7.CHECK FLOOR WIRE NO. 2 (TO GROUND)
C130792E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Terminal Connection
    Specified Condition
    A19-16 (FSP+) - Body ground
    1 MΩ or higher
    A19-24 (FSP-) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


8.CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100887E07
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the center airbag sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

    HINT:
    DTCs other than DTC B1650/32 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed on the tester.


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END