Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

for Preparation Click here


DESCRIPTION

Refer to DTC P0335 .

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft position sensor signal and VVT sensor signal
(2 trip detection logic)
  1. Camshaft timing oil control valve
  2. Oil control valve
  3. Valve timing
  4. ECM

MONITOR DESCRIPTION

The ECM optimizes the valve timing using the Variable Valve Timing (VVT) system to control the intake valve camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake valve camshaft. The ECM calibrates the valve timing of the VVT system by setting the camshaft to the maximum retard angle when the engine speed is idling. The ECM closes the OCV to retard the cam. The ECM stores this valve as "VVT learned value" (when the difference between the target valve timing and the actual valve timing is 5 degrees or less, the ECM stores this in its memory).
If the learned value meets both of the following conditions ("a" and "b"), the ECM interprets this as a defect in the VVT system and sets a DTC.
(a) VVT learning value is less than 30°CA (CA: Crankshaft Angle), or more than 46°CA.
(b) Above condition continues for more than 18 seconds.

MONITOR STRATEGY


Related DTCs
P0016:
VVT system misalignment
Required sensors/components
Crankshaft position sensor, camshaft position sensor
Frequency of operation
Once per driving cycle
Duration
Within 60 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
P0011 (VVT System 1 - Advance)
P0012 (VVT System 1 - Retard)
P0115 - P0118 (ECT sensor)
Engine speed
900 to 5,000 rpm

TYPICAL MALFUNCTION THRESHOLDS


Either of the following conditions is met:
(a) or (b)
(a) VVT learning value at maximum retarded valve timing
Less than 30°CA
(b) VVT learning value at maximum retarded valve timing
More than 46°CA

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK VALVE TIMING (CHECK FOR LOOSE AND A JUMPED TOOTH OF TIMING CHAIN)

OK:
The matchmarks of the crankshaft pulley and camshaft pulley align.



NG
ADJUST VALVE TIMING (REPAIR OR REPLACE TIMING CHAIN)
OK


2.PERFORM ACTIVE TEST BY TECHSTREAM (OPERATE OCV)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

  1. Using Techstream, operate the OCV and check the engine speed.

    OK:
    Tester Operation
    Specified Condition
    OCV is OFF
    Normal engine speed
    OCV is ON
    Rough idle or engine stall

    NOTICE:
    Do not drive the vehicle without deactivating inspection mode, otherwise damaging the transaxle may result.



NG
Go to step 5
OK


3.CHECK DTC OUTPUT RECURS
  1. Clear the DTCs (Click here).

  1. Start the HV main system and warm the engine up.

  1. Drive the vehicle with the shift position in B at vehicle speed of more than 44 mph (70 km/h) approximately for 10 minutes or more.

  1. Read output DTCs using Techstream.

    OK:
    No DTC output.

HINT:
*: DTC P0016 is output when a foreign object in engine oil is caught in some part of the system.
These codes will stay registered even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.



OK
VVT SYSTEM OK
NG


4.INSPECT OIL CONTROL VALVE FILTER


    A091578E01
  1. Remove the air cleaner inlet, bolt and oil control valve filter.

  1. Check for cloggings in the oil control valve filter.

    OK:
    The filter has not clogged.

  1. Reinstall the filter, bolt and air cleaner inlet.

    NOTICE:
    If necessary, clean the filter.



NG
REPLACE OIL CONTROL VALVE FILTER
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

OK:
OCV has no contamination and moves smoothly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT


7.CHECK IF DTC RECURS
  1. Clear the DTCs (Click here).

  1. Start the HV system, and warm the engine up.

  1. Drive the vehicle with the shift position in B at vehicle speed of more than 70 km/h (44 mph) approximately for 10 minutes or more.

  1. Read output DTCs using Techstream.

    OK:
    No DTC output.



NG
REPLACE ECM
OK

END