Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0116
When either of following conditions met (2-trip detection logic):
  1. When cold engine started and engine warmed up, Engine Coolant Temperature (ECT) sensor value does not change.
  2. After warmed up engine started, ECT sensor value does not change when engine stopped and then next cold engine start performed.
  1. Thermostat
  2. ECT sensor

MONITOR DESCRIPTION

  1. Engine coolant temperature (ECT) sensor cold start monitor
    When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.
  1. ECT sensor soak monitor
    After a warmed up engine is started, if the ECT sensor value does not change when the engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.

MONITOR STRATEGY


Related DTCs
P0116: Engine coolant temperature (ECT) sensor output stuck at low engine coolant temperature
P0116: ECT sensor output stuck at high engine coolant temperature
Required Sensors/Components (Main)
ECT sensor
Required Sensors/Components (Related)
Crankshaft position sensor, intake air temperature sensor and mass air flow meter
Frequency of Operation
Once per driving cycle
Duration
250 seconds
MIL Operation
2 driving cycles: ETC sensor output stuck at low engine coolant temperature
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


ECT sensor cold start monitor: 
Monitor will not run if the following DTCs are present
P0100 to P0103: MAF meter
P0110 to P0113: IAT sensor
Battery voltage
10.5 V or more
Time after engine start
1 second or more
ECT at engine start
Less than 60°C (140°F)
IAT sensor circuit
OK
Soak time
0 seconds or more
Accumulated MAF
1367 g or more
Engine
Not running
Fuel cut
OFF
Difference between ECT at engine start and IAT
Less than 40°C (72°F)

ECT sensor soak monitor: 
Monitor runs whenever the following DTCs are not present
P0100 to P0103: MAF meter
P0110 to P0113: IAT sensor
Battery voltage
10.5 V or more
Engine
Running
Soak time
5 hours or more
Either conditions (a) or (b) is met:
-
(a) ECT
60°C (140°F) or more
(b) Accumulated MAF
2966 g or more

TYPICAL MALFUNCTION THRESHOLDS


Engine Coolant Temperature Sensor Cold Start Monitor: 
Variation of engine coolant temperature
Less than 5°C (9°F)

Engine Coolant Temperature Sensor Soak Monitor: 
Variation of engine coolant temperature
Less than 3°C (5.4°F) or less

COMPONENT OPERATING RANGE


ECT
ECT sensor value changes in accordance with actual ECT

WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

1.READ OUTPUT DTC
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0116
    A
    P0116 and other DTCs
    B



B
GO TO DTC CHART
A


2.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Measure the valve opening temperature of the thermostat.

    Standard temperature:
    80°C to 84°C (176°F to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR