Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A1F-129    Battery Energy Control Module

for Preparation Click here


DESCRIPTION

The battery ECU transmits information on the HV battery voltage to the HV control ECU via CAN communication.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A1F
129
HV battery voltage circuit malfunction
  1. HV battery voltage circuit
  2. Service plug grip
  3. High voltage fuse
  4. Battery plug
  5. Battery ECU

MONITOR DESCRIPTION

The HV control ECU calculates the differences between the received HV battery voltage, boost converter voltage, and inverter voltage. If any of the differences exceed prescribed values, the HV control ECU determines that there is a malfunction in the battery voltage circuit. When the HV control ECU detects a malfunction, it illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A1F (INF 129): Battery ECU / Voltage (VB) sensor deviation
Required sensor / components
Battery ECU, boost converter, inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TOYOTA's intellectual property
-

COMPONENT OPERATING RANGE


Battery ECU
Normal

WIRING DIAGRAM


A090438E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV BATTERY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTCs are output



YES
GO TO RELEVANT DTC CHART
NO


2.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTCs listed in the table below are output


    DTC No.
    INF Code
    Detection Item
    See Page
    P0ADC
    226
    Hybrid Battery Positive Contactor Control Circuit High
    Click here
    P0ADB
    227
    Hybrid Battery Positive Contactor Control Circuit Low
    Click here
    P0AE0
    228
    Hybrid Battery Negative Contactor Control Circuit High
    Click here
    P0ADF
    229
    Hybrid Battery Negative Contactor Control Circuit Low
    Click here



YES
GO TO THE PAGE NUMBER SHOWN IN THE TABLE ABOVE
NO


3.INSPECT SERVICE PLUG GRIP

CAUTION:
Wear insulated gloves before performing the following operation.



    A081749E01
  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Measure the resistance between the terminals of the service plug grip.

    Standard resistance:
    Below 1 Ω



NG
Go to step 5
OK


4.INSPECT BATTERY PLUG

CAUTION:
Wear insulated gloves and goggles before performing the following operation.



    A093184E01
  1. Remove the HV battery assembly .

  1. Remove the battery plug .

  1. Measure the resistance between the terminals of the battery plug.

    Standard resistance:
    Tester Connection
    Specified Condition
    A - C
    Below 1 Ω
    B - D
    Below 1 Ω

  1. Reinstall the battery plug .

  1. Reinstall the HV battery assembly .



NG
REPLACE BATTERY PLUG
OK

REPLACE BATTERY ECU ASSEMBLY 

5.INSPECT HIGH VOLTAGE FUSE

CAUTION:
Wear insulated gloves before performing the following operation.



    A057824E01
  1. Remove the high voltage fuse .

    HINT:
    The high voltage fuse is enclosed in the service plug grip.

  1. Measure the resistance between the terminals of the high voltage fuse.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the high voltage fuse .



NG
REPLACE HIGH VOLTAGE FUSE
OK

REPLACE SERVICE PLUG GRIP