Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

The air-fuel ratio (A/F) sensor provides output voltage* which is almost equal to the existing air-fuel ratio. The A/F sensor output voltage is used to provide feedback for the ECM to control the air-fuel ratio.
With the A/F sensor output, the ECM can determine deviation from the stoichiometric air-fuel ratio and control proper injection time. If the A/F sensor is malfunctioning, the ECM is unable to accurately control the air-fuel ratio.
The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), current flows to the heater to heat the sensor to facilitate detection of accurate oxygen concentration.
The A/F sensor is a planar type. Compared to a conventional type, the sensor and heater portions are narrower. Because the heat of the heater is conducted through the alumina to zirconia (of the sensor portion), sensor activation is accelerated.
To obtain a high purification rate of carbon monoxides (CO), hydrocarbons (HC) and nitrogen oxides (NOx) components of the exhaust gas, a three-way catalytic converter is used. The converter is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.
*: The voltage value changes inside the ECM only.

A073819E02


DTC No.
DTC Detection Condition
Trouble Area
P2195
A/F sensor voltage is more than 3.8 V.
  1. Open or short in A/F sensor (bank 1 sensor 1) circuit
  2. A/F sensor (bank 1 sensor 1)
  3. A/F sensor heater
  4. Integration relay
  5. A/F sensor heater and relay circuit
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. PCV hose connection
  10. ECM
A/F sensor current is 3.6 mA or more.
P2196
A/F sensor voltage is less than 2.8 V.
  1. Open or short in A/F sensor (bank 1 sensor 1) circuit
  2. A/F sensor (bank 1 sensor 1)
  3. A/F sensor heater
  4. Integration relay
  5. A/F sensor heater and relay circuit
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. PCV hose connection
  10. ECM
A/F sensor current is less than 1.4 mA.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. After confirming DTC P2195 and P2196, use Techstream to confirm voltage output of A/F sensor (AFS B1 S1) from the "Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1."
  3. The A/F sensor's output voltage and the short-term fuel trim value can be read using Techstream.
  4. The ECM controls the voltage of the A1A+, and A1A- terminals of the ECM to a fixed voltage. Therefore, it is impossible to confirm the A/F sensor output voltage without Techstream.
  5. The OBD II scan tool (excluding Techstream) displays the one fifth of the A/F sensor output voltage which is displayed on Techstream.


MONITOR DESCRIPTION

Under the air-fuel ratio feedback control, if the voltage output of the A/F sensor indicates RICH or LEAN for a certain period of time or more, the ECM concludes that there is a fault in the A/F sensor system. The ECM will turn on the MIL and a DTC is set.
If the A/F sensor voltage output is less than 2.8 V (indicates very RICH) 5 seconds, the ECM sets DTC P2196. Also, the A/F sensor voltage output is more than 3.8 V (indicates very LEAN) for 5 seconds, DTC P2195 is set.

MONITOR STRATEGY


Related DTCs
P2195: A/F sensor signal stuck lean
P2196: A/F sensor signal stuck rich
Required sensors/components
Main: A/F sensor
Related: Heated oxygen sensor
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
P0031, P0032 (A/F sensor heater - Sensor 1)
P0037, P0038 (O2 sensor heater - Sensor 2)
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for Closed Loop)
P0136 (O2 sensor - sensor 2)
P0171, P0172 (Fuel system)
P0300 - P0304 (Misfire)
P0335 (CKP sensor)
P0340 (CMP sensor)
P0455, P0456 (EVAP system)
P0500 (VSS)

Sensor voltage detection monitor (Lean side malfunction P2195): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor voltage detection monitor (Rich side malfunction P2196): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor current detection monitor P2195 and P2196: 
Battery voltage
11 V or more
Atmospheric pressure
76 kPa (570 mmHg) or more
A/F sensor status
Activated
Continuous time of fuel cut
3 to 10 seconds
ECT
75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Sensor voltage detection monitor (Lean side malfunction P2195) 
Rear HO2S voltage
Rises from less than 0.21 V, or 0.59 V or more
A/F sensor output voltage
More than 3.8 V

Sensor voltage detection monitor (Rich side malfunction P2196) 
Rear HO2S voltage
Fails from less than 0.21 V, or 0.59 V or more
A/F sensor output voltage
Less than 2.8 V

Sensor current detection monitor P2195 
A/F sensor current
3.6 mA or more

Sensor current detection monitor P2196 
A/F sensor current
Less than 1.4 mA

WIRING DIAGRAM


A151895E04


CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

A107162E54


A107163E41

  1. (a) Connect Techstream to the DLC3 (a).
  2. (b) Turn the power switch on (IG) (b).
  3. (c) Turn the tester on (c).
  4. (d) Clear the DTCs (Click here) (d).
  5. (e) Put the engine in inspection mode (Click here), warm it up until the ECT reaches 75°C (167°F) or higher (e).
  6. (f) On Techstream, select the following menu items to check the fuel-cut status: Powertrain / Engine / Data List / Idle Fuel Cut (f).
  7. (g) Drive the vehicle at between 40 mph (64 km/h) and 75 mph (120 km/h) for at least 10 minutes (g).
  8. (h) Change the transmission to the B position (h).
  9. (i) Drive the vehicle at a proper vehicle speed to perform fuel-cut operation (i).

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Vehicle speed is 55 mph (88 km/h) or more (fuel injection resumes at 1,000 rpm).

  10. (j) Accelerate the vehicle to 40 mph (64 km/h) or more by depressing the accelerator pedal for at least 10 seconds (j).
  11. (k) Soon after performing step (j) above, release the accelerator pedal for at least 10 seconds without depressing the brake pedal, in order to execute fuel-cut control (k).
  12. (l) Allow the vehicle to decelerate until the vehicle speed declines to less than 40 mph (64 km/h) (l).
  13. (m) Repeat steps from (h) through (k) above at least 3 times in one driving cycle (m).

    HINT:
    Completion of all A/F sensor monitors is required to change the value in TEST RESULT.

    CAUTION:
    Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.


INSPECTION PROCEDURE

HINT:
  1. Although each DTC title says "oxygen sensor", these DTCs are related to the A/F sensor.
  2. Malfunctioning areas can be found by performing the Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor operation. The Control the Injection Volume for A/F Sensor operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble area are malfunctioning or not.

(a) Perform the Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor operation.

HINT:
The Control the Injection Volume for A/F Sensor operation lowers the injection volume 12.5% or increases the injection volume 25%.

(1) Connect Techstream to the DLC3.
(2) Turn the power switch ON (IG).
(3) Put the engine in inspection mode (Click here).
(4) Warm up the engine by running the engine at 2,500 rpm, depressing the accelerator pedal more than 60% for approximately 90 seconds.
(5) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
(6) Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idle condition (press the right or left button).

Result:
A/F sensor reacts in accordance with increase and decrease of injection volume:
+25% → rich output: Less than 3.0 V
-12.5% → lean output: More than 3.35 V
Heated oxygen sensor reacts in accordance with increase and decrease of injection volume:
+25% → rich output: More than 0.55 V
-12.5% → lean output: Less than 0.4 V

NOTICE:
The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.


Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A150444E03
A150447E02
A150444E03
A150446E02
-
2
A150444E03
A150445E02
A150444E03
A150446E02
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150444E03
A150447E02
A150444E03
A150445E02
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150444E03
A150445E02
A150444E03
A150445E02
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
The following Control the Injection Volume for A/F Sensor procedure enables the technician to check and graph the voltage output of both A/F sensor and heated oxygen sensor.
To display the graph, enter Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 then press the graph button on the Data List view.

HINT:
  1. Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. A high A/F sensor voltage could be caused by a RICH air-fuel mixture. Check the conditions that would cause the engine to run with the RICH air-fuel mixture.
  3. A low A/F sensor voltage could be caused by a LEAN air-fuel mixture. Check the conditions that would cause the engine to run with the LEAN air-fuel mixture.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC A/F SENSOR DTCS)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    A/F sensor circuit DTC
    A
    A/F sensor circuit DTCs and other DTCs
    B

    HINT:
    If any other codes besides A/F sensor DTCs are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.READ VALUE OF TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR)
  1. Connect Techstream to the DLC 3.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the A/F sensors (bank 1 sensor 1) by running the engine at 2,500 rpm with the accelerator pedal depressed more than 60% for approximately 90 seconds.

  1. Read A/F sensor voltage output on Techstream.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Select "AFS B1 S1/Engine Speed" and press button "YES".

  1. Monitor the A/F sensor voltage carefully.

  1. Check the A/F sensor voltage output under the following conditions:

    1. Put the engine in inspection mode and allow the engine to idle for 30 seconds.

    2. Put the engine in inspection mode and running the engine at 2,500 rpm with the accelerator pedal depressed more than 60% (where the engine RPM is not suddenly changed).

    3. Deactivate the inspection mode and drive the vehicle with shift position "B" range.

    4. Accelerate the vehicle to 70 km/h (44 mph) and quickly release the accelerator pedal so that the throttle valve is fully closed.

CAUTION:
  1. Strictly observe of posted speed limits, traffic laws, and road conditions when performing these drive patterns.
  2. Do not drive the vehicle without deactivating inspection mode, otherwise damaging the transaxle may result.

OK:
Condition (1) and (2)
Voltage changes in the vicinity of 3.3 V (between approximately 3.1 to 3.5 V) as shown in the illustration.
Condition (4)
A/F sensor voltage increases to 3.8 V or more during engine deceleration (when fuel cut) as shown in the illustration.


A072304E23

HINT:
  1. Whenever the output voltage of the A/F sensor remains at approximately 3.3 V (see diagram Malfunction Condition) under any condition as well as the above conditions, the A/F sensor may have an open-circuit. (This will happen also when the A/F sensor heater has an open-circuit.)
  2. Whenever the output voltage of the A/F sensor remains at a certain value of approximately 3.8 V or more, or 2.8 V or less (see diagram Malfunction Condition) under any condition as well as the above conditions, the A/F sensor may have a short-circuit.
  3. The ECM will stop fuel injection (fuel cut) during engine deceleration. This will cause a LEAN condition and should result in a momentary increase in A/F sensor voltage output.
  4. The ECM must establish a closed throttle position learned value to perform fuel cut. If the battery terminal was reconnected, the vehicle must be driven over 10 mph to allow the ECM to learn the closed throttle position.
  5. When the vehicle is driven:
    The output voltage of the A/F sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
  6. The A/F sensor is a current output element, and therefore the current is converted into voltage inside the ECM. If measuring voltage at connectors of A/F sensor or ECM, you will observe a constant voltage.



OK
Go to step 13
NG


3.INSPECT AIR FUEL RATIO SENSOR (RESISTANCE OF A/F SENSOR HEATER)


    A085152E51
  1. Disconnect the A5 A/F sensor connector.

  1. Measure the resistance between the terminals of the A/F sensor.

    Standard resistance:
    Tester Connection
    Resistance
    1 (HT) - 2 (+B)
    1.8 to 3.4 Ω at 20°C (68°F)

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


4.INSPECT INTEGRATION RELAY (EFI M RELAY)


    A082812E01
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI M relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3K-1 - 3I-8
    10 kΩ or higher
    3K-1 - 3I-8
    Below 1 Ω
    (Apply battery voltage to terminals 3I-6 and 3I-7)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A085153E07

B062793E17

  1. Disconnect the A5 A/F sensor connector.



    A065745E71
  1. Disconnect the E5 ECM connector.

  1. Check the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A5-3 (AF+) - E5-23 (A1A+)
    Below 1 Ω
    A5-4 (AF-) - E5-22 (A1A-)
    Below 1 Ω
    A5-1 (HT) - E5-7 (HA1A)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A5-3 (AF+) or E5-23 (A1A+) - Body ground
    10 kΩ or higher
    A5-4 (AF-) or E5-22 (A1A-) - Body ground
    10 kΩ or higher
    A5-1 (HT) or E5-7 (HA1A) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check for vacuum leaks in the air induction system.

    OK:
    No leakage in the air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.CHECK FUEL PRESSURE

OK:
Fuel pressure: 304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check injector injection (high or low fuel injection quantity or poor injection pattern).

    OK:
    Injection volume: 36 to 46 cm3 (2.1 to 2.8 cu in.) per 15 seconds.



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


9.REPLACE AIR FUEL RATIO SENSOR

NEXT


10.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs prior to performing the confirmation driving pattern.


NEXT


11.READ OUTPUT DTCS (SEE IF A/F SENSOR DTCS ARE OUTPUT AGAIN)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs using Techstream.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    A/F sensor circuit DTCs
    B



B
REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A


12.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

OK:
The vehicle has run out of fuel in the past.



NO
CHECK FOR INTERMITTENT PROBLEMS
YES

DTCS ARE CAUSED BY RUNNING OUT OF FUEL 

13.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs prior to performing the confirmation driving pattern.


NEXT


14.READ OUTPUT DTCS (SEE IF A/F SENSOR DTCS ARE OUTPUT AGAIN)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs using Techstream.

    Result:
    Display (DTC Output)
    Proceed to
    A/F sensor circuit DTCs
    A
    No output
    B



B
Go to step 18
A


15.REPLACE AIR FUEL RATIO SENSOR

NEXT


16.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs prior to performing the confirmation driving pattern.


NEXT


17.READ OUTPUT DTCS (SEE IF A/F SENSOR DTCS ARE OUTPUT AGAIN)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs using Techstream.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    A/F sensor circuit DTCs
    B



B
REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A


18.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

OK:
The vehicle has run out of fuel in the past.



NO
CHECK FOR INTERMITTENT PROBLEMS
YES

DTCS ARE CAUSED BY RUNNING OUT OF FUEL