Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › CAMSHAFT POSITION SENSOR

CAMSHAFT POSITION SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT POSITION SENSOR
  1. Install the sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the sensor connector.



2. INSTALL INVERTER WITH CONVERTER
  1. Install the inverter with converter (Click here).



3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


4. ADD HV COOLANT


    C098376E01
  1. Loosen the bleeder plug shown in the illustration and connect a hose.

    NOTICE:
    Insert one end of the hose into the bleeder tank.



    C098377E01
  1. Add coolant until the level of coolant in the hose attached to the bleeder tank reaches the same level as the FULL line of the reserve tank.

    NOTICE:
    Add genuine Toyota Super LLC coolant.

  1. Close the bleeder plug.

  1. Turn the power switch ON (IG) and run the water pump for approximately 20 seconds.

  1. Turn the power switch OFF. (*1)

  1. Loosen the bleeder plug and bleed the air from the transaxle. (*2)

  1. Add coolant into the bleeder tank. (*3)

  1. Repeat the steps *1, *2 and *3.

    Standard:
    Water pump noise becomes softer and coolant circulation in reserve tank improves. Coolant system air bleeding is complete

    HINT:
    If air remains in the coolant system, the water pump noise becomes louder and the coolant circulation in the reserve tank becomes worse.

  1. Turn the power switch ON (IG) and run the water pump for approximately 5 minutes after completing air bleeding of the coolant system.

    NOTICE:
    Ensure that the bleeder plug is closed.



    C098378E01
  1. Add coolant until the reserve tank is filled up to the FULL mark.



5. ADD ENGINE COOLANT
  1. Tighten the drain cock plug of the coolant heat storage tank, then disconnect the vinyl hose.

  1. Tighten the drain cock plug of the engine, then disconnect the vinyl hose.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }

  1. Tighten the drain cock plug of the radiator, then disconnect the vinyl hose.



    A092991E01
  1. Connect a vinyl hose to the bleeder plug of the radiator assembly and the radiator reservoir.

    HINT:
    Insert the vinyl hose inside the radiator reservoir tank.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Fill the radiator with coolant up to the fill port.

    Standard capacity:
    8.6 liters (9.1 US qts, 7.6 Imp. qts)

    HINT:
    1. When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.
    2. Amount of coolant to fill: Approximately 2.4 liters (2.5 US qts, 2.1 Imp. qts)
    3. Use of improper coolants may damage the engine cooling system.
    4. Only use "Toyota Super Long Life Coolant", or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
    5. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene-glycol concentration is approximately 50% and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    6. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add more coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cop.

  1. Fill the radiator reservoir tank with coolant to the full level.

  1. Connect the coolant heat storage water pump connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Select the item:
    Powertrain / Engine and ECT / Data List/Activate the Water Pump

    NOTICE:
    1. The water pump motor operates for 30 seconds after WATER PUMP is ON in the ACTIVE TEST mode, then it automatically stops operating.
    2. Do not actuate the water pump motor without coolant filled.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Remove the radiator cap, then fill the radiator with coolant up to the fill port.

    HINT:
    When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cap.

  1. Slowly pour coolant into the radiator reservoir until it reaches the full line.

  1. Disconnect the vinyl hose between the bleeder plug of the radiator assembly and the radiator reservoir tank.

  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine until the thermostat is open.

  1. Stop the engine, then wait until the coolant becomes cold. Remove the radiator cap and check the coolant level.

    CAUTION:
    If the engine or radiator is hot, do not remove the radiator cap.

    If the coolant level is lower, add coolant again. Warm up the engine, then check the coolant level.

  1. When the coolant level stops going down, add coolant to the radiator reservoir tank up to the full level.



6. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A088171E01
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 177 kPa (1.8 kgf/cm2, 25.6 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.



7. INSPECT FOR COOLANT LEAK (for Inverter)


8. INSTALL RADIATOR SUPPORT OPENING COVER


    A087414E01
  1. Install the cover with the 6 clips.



9. INSTALL ENGINE UNDER COVER RH


10. INSTALL ENGINE UNDER COVER LH


11. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.