ENGINE COOLANT TEMPERATURE SENSOR > INSTALLATION |
| 1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Using a 19 mm deep socket wrench, install a new gasket and the sensor.
Connect the sensor connector.
| 2. INSTALL INVERTER WITH CONVERTER |
Install the inverter with converter (Click here).
| 3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 4. ADD ENGINE COOLANT |
Tighten the drain cock plug of the coolant heat storage tank, then disconnect the vinyl hose.
Tighten the drain cock plug of the engine, then disconnect the vinyl hose.
Tighten the drain cock plug of the radiator, then disconnect the vinyl hose.
![]() |
Connect a vinyl hose to the bleeder plug of the radiator assembly and the radiator reservoir.
![]() |
Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.
Fill the radiator with coolant up to the fill port.
Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.
Install the radiator cop.
Fill the radiator reservoir tank with coolant to the full level.
Connect the coolant heat storage water pump connector.
Connect the Techstream to the DLC3.
Turn the power switch ON (IG).
Select the item:
Powertrain / Engine and ECT / Data List/Activate the Water Pump
![]() |
Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.
Remove the radiator cap, then fill the radiator with coolant up to the fill port.
Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.
Install the radiator cap.
Slowly pour coolant into the radiator reservoir until it reaches the full line.
Disconnect the vinyl hose between the bleeder plug of the radiator assembly and the radiator reservoir tank.
Set the vehicle to inspection mode (Click here).
Warm up the engine until the thermostat is open.
Stop the engine, then wait until the coolant becomes cold. Remove the radiator cap and check the coolant level.
When the coolant level stops going down, add coolant to the radiator reservoir tank up to the full level.
| 5. ADD HV COOLANT |
![]() |
Loosen the bleeder plug shown in the illustration and connect a hose.
![]() |
Add coolant until the level of coolant in the hose attached to the bleeder tank reaches the same level as the FULL line of the reserve tank.
Close the bleeder plug.
Turn the power switch ON (IG) and run the water pump for approximately 20 seconds.
Turn the power switch OFF. (*1)
Loosen the bleeder plug and bleed the air from the transaxle. (*2)
Add coolant into the bleeder tank. (*3)
Repeat the steps *1, *2 and *3.
Turn the power switch ON (IG) and run the water pump for approximately 5 minutes after completing air bleeding of the coolant system.
![]() |
Add coolant until the reserve tank is filled up to the FULL mark.
| 6. INSPECT FOR COOLANT LEAK (for Engine) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 177 kPa (1.8 kgf/cm2, 25.6 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.
| 7. INSPECT FOR COOLANT LEAK (for Inverter) |
| 8. INSTALL ENGINE UNDER COVER RH |
| 9. INSTALL ENGINE UNDER COVER LH |
| 10. INSTALL RADIATOR SUPPORT OPENING COVER |
![]() |
Install the cover with the 6 clips.
| 11. PERFORM INITIALIZATION |
Perform initialization (Click here).