Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) > Only Wireless Door Lock Control Function does not Operate

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU through the certification ECU. The main body ECU then controls all doors by sending LOCK/UNLOCK signals to each door lock.

WIRING DIAGRAM


B150420E01


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Refer to operation check (Click here).



OK
NORMAL
NG


2.CHECK THAT TRANSMITTER LED LIGHTS UP
  1. Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.

    OK:
    Transmitter's LED illuminates 3 times when switch is pressed 3 times.



NG
Go to step 4
OK


3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS (STANDARD OPERATION)
  1. Check standard UNLOCK/LOCK switch operation.

    NOTICE:
    Standardized test procedure:
    Press the transmitter switch for 1 second, directing the transmitter to the driver side door outside handle from a distance of 1 m (3.28 ft.). The transmitter should be pointed directly at the handle, i.e. at a 90° angle to the vehicle body.

    OK:
    Doors can be locked and unlocked with transmitter switches.



NG
Go to step 5
OK

REPLACE DOOR CONTROL TRANSMITTER 

4.CHECK TRANSMITTER BATTERY (OPERATION)
  1. Temporarily replace the transmitter battery with a new or normally functioning one (Click here).

  1. Check that the doors can be locked and unlocked by using the transmitter LOCK/UNLOCK switch.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL TRANSMITTER
OK

END (TRANSMITTER BATTERY IS DEFECTIVE) 

5.SWITCH TO SELF-DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode using the Techstream.

    1. Connect the Techstream (with CAN VIM) to the DLC3.

    2. Turn the power switch ON (IG) and push the Techstream main switch ON.

      HINT:
      Please refer to the Techstream operator's manual for further details.

  1. Switch to self-diagnostic mode by operating the key.

    1. Put the vehicle under the vehicle's initial condition (Click here), insert the key into the key slot and remove it.

    2. Within 5 seconds of removing the key (step above), insert the key into the key slot. Then turn the power switch ON (IG) and OFF.

    3. Within 30 seconds of switching the power switch OFF again (step above), perform the following 9 times:
      Turn the power switch ON (IG) and OFF*.

      NOTICE:
      If the change to self-diagnostic mode has failed, the system will return to normal mode.

      HINT:
      1. Turning the power switch ON (IG) after step* has been completed will end self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.



    B052341E09
  1. Check that the system has switched to self-diagnostic mode by checking the flashes of the room light (dome light or key slot light). Compare the flash patterns of the room light to the timing chart on the illustration.

    OK:
    Flash patterns of room light should be the same as that shown in timing chart on illustration.



NG
Go to step 9
OK


6.CHECK BY SELF-DIAGNOSTIC MODE


  1. Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.


    B127179E02


    Result: 
    Result
    Proceed to
    Unmatched recognition code is output
    A
    Normal waves (patterns of room light) for LOCK, UNLOCK and PANIC switches are output
    B
    No diagnosis outputs are present
    C



B
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU)

C
Go to step 8
A


7.REGISTER RECOGNITION CODE
  1. Check that the system can switch to rewrite mode or add mode and that a recognition code can be registered (Click here).

    OK:
    System can switch to rewrite mode or add mode and recognition code can be registered.



NG
Go to step 15
OK

END 

8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
  1. Temporarily replace the door control receiver with a new or normally functioning one.

  1. Check that an unmatching recognition code is output when the door lock control transmitter switch is held down.

    OK:
    Unmatching recognition code is output.



NG
Go to step 13
OK

REPLACE DOOR CONTROL TRANSMITTER 

9.CONFIRM INPUT METHOD OF SELF-DIAGNOSTIC MODE

Result: 
Result
Proceed to
Method for changing system self-diagnostic mode works
A
Method for changing system self-diagnostic mode does not work
B


B
Go to step 5
A


10.INSPECT KEY SLOT


    B127180E02
  1. Measure the resistance of the halfway switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 4
    No key is in key slot
    10 kΩ or higher
    Key is in key slot
    Below 1 Ω



NG
REPLACE KEY SLOT
OK


11.CHECK WIRE HARNESS (CERTIFICATION ECU - DRIVER SIDE JUNCTION BLOCK AND KEY SLOT)

B127181E03

  1. Disconnect the S11 connector.

  1. Disconnect the K2 slot connector.

  1. Disconnect the 1E junction block connector.

  1. Measure the resistance of wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S11-4 (KSW) - 1E-23 (KSW)
    Below 1 Ω
    K2-4 (KSW1) - 1E-26 (KSW)
    K2-2 (COM) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12.CHECK WIRE HARNESS (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)


    B127182E04
  1. Disconnect the D4 receiver connector.

  1. Measure the voltage and resistance of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    D4-5 (+5) - Body ground
    10 to 14 V

    Standard resistance:
    Tester Connection
    Specified Condition
    D4-1 (GND) - Body ground
    Below 1 Ω
    D4-2 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


13.CHECK WIRE HARNESS (DOOR CONTROL RECEIVER - CERTIFICATION ECU)


    B127176E04
  1. Disconnect the D4 receiver connector.

  1. Disconnect the S11 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D4-4 (DATA) - S11-10 (RDA)
    Below 1 Ω
    D4-3 (RSSI) - S11-11 (RSSI)
    D4-4 (DATA) - S11-10 (RDA) - Body ground
    10 kΩ or higher
    D4-3 (RSSI) - S11-11 (RSSI) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


14.CHECK DOOR CONTROL RECEIVER (OUTPUT)


    B127180E04
  1. Reconnect the D4 receiver connector.

  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D4-3 (RSSI) - Body ground
    Transmitter switch OFF (power switch OFF and all doors closed)
    Below 1 V
    D4-3 (RSSI) - Body ground
    Transmitter switch ON (power switch OFF and all doors closed)
    Alternating between 6 to 7 V and below 1 V



OK
Go to step 16
NG


15.CHECK DOOR CONTROL TRANSMITTER (OPERATION)
  1. Temporarily replace the door control transmitter with a new or normally functioning one.

  1. Check that the doors can be locked and unlocked by using the transmitter LOCK/UNLOCK switch.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL RECEIVER
OK

END (DOOR CONTROL TRANSMITTER IS DEFECTIVE) 

16.CHECK CERTIFICATION ECU (OPERATION)
  1. Temporarily replace the certification ECU with a new or normally functioning one.

  1. Check that the door can be locked and unlocked by using the transmitter LOCK/UNLOCK switch.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU)
OK

END (CERTIFICATION ECU IS DEFECTIVE)