FUEL SYSTEM > PRECAUTION |
| 1.PRECAUTION |
Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
Do not work on the fuel system near fire. Never smoke while performing work.
Keep rubber or leather parts away from gasoline.
| 2.DISCHARGE FUEL SYSTEM PRESSURE |
Set the vehicle to "INSPECTION MODE1" (Click here).
Disconnect the cable from the negative (-) battery terminal.
Remove the rear seat cushion .
Remove the rear floor service hole cover.
![]() |
Disconnect the fuel pump connector.
Connect the cable to the negative (-) battery terminal.
Start the engine.
After the engine stops (rough idle), turn the power switch OFF.
Crank the engine again, then check that the engine does not start.
Remove the fuel tank cap, then discharge the pressure in the fuel tank completely.
Disconnect the cable from the negative (-) battery terminal.
Connect the fuel pump connector.
Install the rear floor service hole cover.
Install the rear seat cushion .
Connect the cable to the negative (-) battery terminal.
Perform initialization (Click here).
| 3.FUEL SYSTEM |
When disconnecting the high-pressure fuel line, a large amount of gasoline will spill out. So take the following precautions.
![]() |
Discharge the fuel system pressure (see step DISCHARGE FUEL SYSTEM PRESSURE).
Disconnect the fuel pump tube.
Drain the pressure remaining in the fuel pump tube.
Cover the disconnected fuel pump tube (fuel tube joint and fuel tube connector) with a plastic bag to prevent damage and intrusion of foreign objects.
Take the following precautions when removing and installing the fuel injector.
![]() |
Do not reuse the O-ring.
Do not damage a new O-ring when installing it to the fuel injector.
Before installing a new O-ring, apply spindle oil or gasoline.
![]() |
Install the fuel injector to the fuel delivery pipe and cylinder head as illustrated.
Take the following precautions when removing the fuel tube connector (Type A).
![]() |
Check the fuel tube connector and pipe for dirt or mud before removing the fuel tube connector.
If they are dirty, wipe them off with a shop rag.
Pinch the retainer as illustrated, then pull out the fuel tube connector from the pipe.
![]() |
If the fuel tube connector and pipe are stuck, pinch the pipe, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.
After removing the fuel tube, check the sealing surface of the pipe for dirt or mud.
If it is dirty, wipe it off with a shop rag.
![]() |
Cover the disconnected fuel tube connector and pipe with a plastic bag to prevent damage and intrusion of foreign objects.
Take the following precautions when installing the fuel tube connector (Type A).
![]() |
Align the fuel tube connector with the pipe, then push in the fuel tube connector until the retainer makes a "click" sound.
![]() |
After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by pulling them.
![]() |
Take the following precautions when removing the fuel tube connector (Type B).
Check the fuel tube connector and pipe for dirt or mud before removing the fuel tube connector.
If they are dirty, wipe them off with a shop rag.
Pinch the retainer as illustrated, then pull out the fuel tube connector from the pipe.
![]() |
If the fuel connector and pipe are stuck, pinch the pipe, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.
After removing the fuel tube, check the sealing surface of the pipe for dirt or mud.
If it is dirty, wipe it off with a shop rag.
![]() |
Cover the disconnected fuel tube connector and pipe with a plastic bag to prevent damage and intrusion of foreign objects.
Take the following precautions when installing the fuel tube connector (Type B).
![]() |
Align the fuel tube connector with the pipe, then push in the fuel tube connector until the retainer makes a "click" sound.
![]() |
After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by pulling them.
| 4.INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks after doing maintenance on the fuel system (Click here).