Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in CAN Main Wire

for Preparation Click here


DESCRIPTION

There may be an open circuit in the CAN main wire and / or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
  1. CAN main wire and connector
  2. J/C1 (Junction connector)
  3. J/C2 (Junction connector)
  4. DLC3 branch wire and connector
  5. ECM
  6. Battery ECU

WIRING DIAGRAM


C126184E04


INSPECTION PROCEDURE

1.CHECK DLC3
H100769E13
  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    108 to 132 Ω
    A
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    132 Ω or more
    B

    NOTICE:
    When the measured value is 132 Ω or more and the CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



B
REPLACE DLC3 BRANCH WIRE AND CONNECTOR (CANH, CANL)
A


2.CHECK CAN MAIN WIRE FOR DISCONNECTION (CAN BUS CHECK)
  1. Perform "CAN Bus Check" using the Techstream via the CAN VIM (Click here).

    Result 
    Result
    Proceed to
    Only "Engine" is not displayed
    A
    Only "HV Battery" is not displayed
    B
    Other ("Engine" and "HV Battery" are not displayed)
    C



B
Go to step 4

C
Go to step 5
A


3.CHECK CAN MAIN WIRE FOR DISCONNECTION (ECM - J/C2)


    C127794E03
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-31 (CANH) - E6-30 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (ECM - J/C2)
OK

REPLACE ECM 

4.CHECK CAN MAIN WIRE FOR DISCONNECTION (BATTERY ECU - J/C1)


    C126181E03
  1. Disconnect the B11 battery ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B11-18 (CANH) - B11-19 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (BATTERY ECU - J/C1)
OK

REPLACE BATTERY ECU 

5.CHECK CAN MAIN WIRE FOR DISCONNECTION (J/C1 - ECM)


    C127797E01
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J15-17 (CANH) - J15-6 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
Go to step 8
OK


6.CONNECT CONNECTOR
  1. Reconnect the J15 J/C1 connector.


NEXT


7.CHECK CAN MAIN WIRE FOR DISCONNECTION (BATTERY ECU - J/C1)


    C126181E03
  1. Disconnect the B11 battery ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B11-18 (CANH) - B11-19 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (BATTERY ECU - J/C1)
OK

REPLACE BATTERY ECU 

8.CONNECT CONNECTOR
  1. Reconnect the J15 J/C1 connector.


NEXT


9.CHECK CAN MAIN WIRE FOR DISCONNECTION (J/C2 - J/C1)


    C127797E02
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J18-18 (CANH) - J18-7 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (J/C2 - J/C1)
OK


10.CONNECT CONNECTOR
  1. Reconnect the J18 J/C2 connector.


NEXT


11.CHECK CAN MAIN WIRE FOR DISCONNECTION (ECM - J/C2)


    C127794E03
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-31 (CANH) - E6-30 (CANL)
    Power switch OFF
    108 to 132 Ω



NG
REPLACE CAN MAIN WIRE AND CONNECTOR
OK

REPLACE ECM