Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



CAN BUS CHECK
  1. Using the Techstream, select "CAN Bus Check" from the "System Select".


CHECK FOR INSTALLED SYSTEMS (ECU & SENSOR) THAT USE CAN COMMUNICATION
  1. The systems (ECU, sensor) that use CAN communication vary depending on the vehicle's optional settings. Check which systems (ECU, sensor) are installed on the vehicle.

    ECU / Sensor name
    Installed to
    Hybrid Vehicle Control ECU
    All vehicles
    Battery ECU
    All vehicles
    ECM
    All vehicles
    Skid Control ECU
    All vehicles
    Power Steering ECU
    All vehicles
    Gateway ECU
    All vehicles
    Steering Angle Sensor
    Vehicle with enhanced VSC (VSC warning light is installed in combination meter)
    Yaw Rate Sensor
    Vehicle with enhanced VSC (VSC warning light is installed in combination meter)

    HINT:
    If enhanced VSC is not installed, neither the yaw rate sensor nor the steering angle sensor is used.


DTC TABLE BY ECU

HINT:
If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).

  1. HYBRID VEHICLE CONTROL ECU

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Information Code
    Detection Item
    U0100
    211, 212, 530
    Lost Communication With ECM / PCM "A"
    U0111
    208, 531
    Lost Communication With Battery Energy Control Module "A"
    U0129
    220, 222, 528, 529
    Lost Communication With Brake System Control Module
    U0131
    433, 434
    Lost Communication With Power Steering Control Module
    U0146
    435
    Lost Communication With Gateway "A"
    P3108
    594
    Lost Communication With A/C System Control Module

  2. BATTERY ECU

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication With ECM / PCM "A"
    U0293
    Lost Communication With Hybrid Vehicle Control System

  3. ECM

    HINT:
    DTC communication uses the CAN communication system.

    DTC No.
    Detection Item
    U0293
    Lost Communication With Hybrid Vehicle Control System

  4. SKID CONTROL ECU

    HINT:
    DTC communication uses the SIL line.


    DTC No.
    Information Code
    Detection Item
    U0293
    152, 153, 154
    Lost Communication With Hybrid Vehicle Control System
    U0073
    360
    Control Module Communication Bus Off
    U0123
    -
    Lost Communication With Yaw Rate Sensor Module
    U0124
    -
    Lost Communication With Lateral Acceleration Sensor Module
    U0126
    -
    Lost Communication With Steering Angle Sensor Module
    with Enhanced VSC

  5. GATEWAY ECU

    HINT:
    The gateway ECU is connected to the CAN communication system but CAN communication system DTCs are not output.

  6. POWER STEERING ECU

    HINT:
    DTC communication uses the SIL line.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off
    U0121
    Lost Communication With Anti-Lock Brake System (ABS) Control Module


DTC COMBINATION TABLE
  1. Perform troubleshooting according to the combination of DTCs output.

    DTC
    Detected Communication Stop Mode
    Output from
    Output DTC
    HYBRID VEHICLE CONTROL ECU COMMUNICATION STOP MODE
    ECM COMMUNICATION STOP MODE
    BATTERY ECU COMMUNICATION STOP MODE
    SKID CONTROL ECU COMMUNICATION STOP MODE
    STEERING ANGLE SENSOR COMMUNICATION STOP MODE
    YAW RATE SENSOR COMMUNICATION STOP MODE
    POWER STEERING ECU COMMUNICATION STOP MODE
    GATEWAY ECU COMMUNICATION STOP MODE
    Hybrid Vehicle Control ECU
    U0100
    -
    ○
    X
    X
    X
    X
    X
    X
    U0111
    -
    X
    ○
    X
    X
    X
    X
    X
    U0129
    -
    X
    X
    ○
    X
    X
    X
    X
    U0146
    -
    X
    X
    X
    X
    X
    X
    ○
    P3108-594
    -
    X
    X
    X
    X
    X
    X
    ○
    ECM
    U0293
    ○
    -
    X
    X
    X
    X
    X
    X
    Battery ECU
    U0100
    X
    ○
    -
    X
    X
    X
    X
    X
    U0293
    ○
    X
    -
    X
    X
    X
    X
    X
    Skid Control ECU
    U0123
    X
    X
    X
    -
    X
    ○
    X
    X
    U0124
    X
    X
    X
    -
    X
    ○
    X
    X
    U0126
    X
    X
    X
    -
    ○
    X
    X
    X
    U0293
    ○
    X
    X
    -
    X
    x
    X
    X
    Power Steering ECU
    U0121
    X
    X
    X
    ○
    X
    X
    -
    X

    HINT:
    ○: Outputs
    x: Not output
    -: Undetectable

    NOTICE:
    1. If U0146 or P3108-594 is output, check the "MULTIPLEX COMMUNICATION SYSTEM" (Click here) before proceeding to "GATEWAY ECU COMMUNICATION STOP MODE".
    2. If U0100-211 or U0111-208 is output separately by the hybrid control ECU, refer to "HYBRID CONTROL SYSTEM" (Click here).

    HINT:
    1. HYBRID VEHICLE CONTROL ECU COMMUNICATION STOP MODE (Click here ).
    2. ECM COMMUNICATION STOP MODE (Click here).
    3. BATTERY ECU COMMUNICATION STOP MODE (Click here).
    4. SKID CONTROL ECU COMMUNICATION STOP MODE (Click here).
    5. STEERING ANGLE SENSOR COMMUNICATION STOP MODE (Click here).
    6. YAW RATE SENSOR COMMUNICATION STOP MODE (Click here).
    7. POWER STEERING ECU COMMUNICATION STOP MODE (Click here).
    8. GATEWAY ECU COMMUNICATION STOP MODE (Click here).