Home › STEERING › STEERING COLUMN › STEERING CONTROL ECU

STEERING CONTROL ECU > INSTALLATION

for Preparation Click here



1. INSTALL POWER STEERING ECU


G028403E01
  1. Install the ECU with the 3 screws.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }



    G028402E01
  1. Connect the 4 ECU connectors.

  1. Install the torque sensor wire harness clamp to the ECU.



2. INSTALL INSTRUMENT PANEL SAFETY PAD
  1. Attach the 6 claws and 3 clips to install the instrument panel.

  1. Install the 2 bolts.



  1. Install the 3 screws.


    B075862E03



3. INSTALL PASSENGER AIRBAG CONNECTOR


H043757E02
  1. Connect the front passenger airbag connector.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.



4. INSTALL FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Attach the 2 clips to install the pillar garnish.

  1. w/ Curtain Shield Airbag:
    Remove the protective cover.



  1. w/ Curtain Shield Airbag:
    Install the pillar garnish.



      B132621E01
    1. Set the claws of the pillar garnish to the area labeled C.

    2. Insert the tip of clip A into the pillar garnish's hole.

    3. Using needle-nose pliers, rotate the tip of clip A 90°. Then push the pillar garnish toward the vehicle body to attach the base of clip A and clip B.



5. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



6. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH


    B136013E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Attach the 5 claws to install the corner piece.



7. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH

HINT:
Use the same procedures described for the LH side.



8. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY (w/ JBL Sound System)


9. INSTALL GLOVE COMPARTMENT DOOR


B074053E03
  1. Attach the claw and 2 clips to install the glove compartment door.

  1. Install the 2 screws.



10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
  1. Attach the 2 hinges to install the door.



    B074051E03
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, engage it to the 2 stoppers.



11. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


12. INSTALL MULTI-DISPLAY ASSEMBLY


I039616E01
  1. Connect the connector and install the multi-display.

  1. Install the 2 bolts.



13. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


B074049E03
  1. Attach the 2 claws and 4 clips to install the instrument panel register.



14. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


B074048E03
  1. Attach the 6 clips to install the instrument panel register.



15. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


B074047E03
  1. Connect the connector.

  1. Attach the claw and 5 clips to install the instrument panel register.



16. INSTALL INSTRUMENT PANEL FINISH PANEL UPPER SUB-ASSEMBLY


B074046E03
  1. Connect the connector.

  1. Attach the 3 claws and 4 clips to install the instrument panel finish panel.



17. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER SUB-ASSEMBLY


B074045E03
  1. Connect the connectors.

  1. Attach the 4 claws and 5 clips to install the instrument panel finish panel.

  1. Connect the hood lock control cable.

  1. Install the 2 screws.



18. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


B074044E03
  1. Attach the 2 claws and 4 clips to install the instrument panel register.



19. CONNECT CABLE TO BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



20. INSTALL NO. 3 REAR FLOOR BOARD


21. INSTALL REAR DECK FLOOR BOX


22. INSTALL NO. 2 REAR FLOOR BOARD


23. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).



24. PERFORM CALIBRATION
  1. Perform calibration (Click here).