Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A373795E01
1.344,1.813 1.813,1.563 false 0.552,3.906 0.906,4.167 0.354,0.26 10 false -20 0.625,4.063 0.781,4.26 0.156,0.198 10 false -4 0.969,4.063 1.188,4.271 0.219,0.208 10 false 32 1.344,4.063 1.615,4.323 0.271,0.26 10 false 68 1.677,4.063 1.958,4.302 0.281,0.24 10 false 104 3.052,4.063 3.406,4.313 0.354,0.25 10 false (°F) 3.042,3.875 3.385,4.125 0.344,0.25 10 false (°C) 1.552,4.354 2.448,4.583 0.896,0.229 10 false Temperature 0.073,0.01 0.615,0.281 0.542,0.271 10 false Fig. 1: 0.083,0.26 1.146,0.552 1.063,0.292 10 false Resistance 0.396,0.479 0.969,0.792 0.573,0.313 10 false (kΩ) 0.281,0.646 0.521,0.906 0.24,0.26 10 false 30 0.281,0.854 0.51,1.125 0.229,0.271 10 false 20 0.281,1.177 0.5,1.385 0.219,0.208 10 false 10 0.354,1.51 0.594,1.76 0.24,0.25 10 false 5 0.344,1.76 0.604,2 0.26,0.24 10 false 3 0.344,2 0.594,2.26 0.25,0.26 10 false 2 0.354,2.313 0.656,2.583 0.302,0.271 10 false 1 0.25,3.458 0.5,3.698 0.25,0.24 10 false 0.1 0.25,3.135 0.49,3.385 0.24,0.25 10 false 0.2 0.25,2.917 0.5,3.167 0.25,0.25 10 false 0.3 0.26,2.677 0.531,2.927 0.271,0.25 10 false 0.5 1.865,1.448 2.688,1.75 0.823,0.302 10 false Acceptable 1,3.896 1.354,4.156 0.354,0.26 10 false 0 1.344,3.896 1.698,4.156 0.354,0.26 10 false 20 1.729,3.896 2.083,4.156 0.354,0.26 10 false 40 2.104,3.896 2.458,4.156 0.354,0.26 10 false 60 2.448,3.896 2.802,4.156 0.354,0.26 10 false 80 2.729,3.896 3.083,4.156 0.354,0.26 10 false 100 2.042,4.063 2.323,4.302 0.281,0.24 10 false 140 2.385,4.063 2.667,4.302 0.281,0.24 10 false 176 2.729,4.063 3.01,4.302 0.281,0.24 10 false 212

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0113 An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM



HINT:

When any of these DTCs are output, check the intake air temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0112 or P0113.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255126E25
0.215,2.734 0.615,2.881 0.401,0.147 10 C21 0.215,2.901 2.815,3.241 2.600,0.339 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 1.603,1.487 1.906,1.641 0.303,0.153 10 THA 1.709,2.096 1.907,2.243 0.198,0.147 10 E2 1.987,1.492 2.094,1.641 0.107,0.149 10 1 1.987,2.096 2.094,2.245 0.107,0.149 10 2 5.409,1.487 5.712,1.641 0.303,0.153 10 THA 5.163,1.492 5.338,1.637 0.175,0.146 10 90 5.092,2.095 5.377,2.241 0.285,0.146 10 122 5.409,2.096 5.814,2.249 0.406,0.153 10 ETHA 5.989,1.366 6.116,1.521 0.128,0.155 10 R 6.014,1.076 6.259,1.226 0.245,0.150 10 5 V 5.672,3.271 6.010,3.425 0.339,0.155 10 ECM 5.665,3.117 6.666,3.264 1.000,0.147 10 C10*1, C9*2 3.372,3.223 4.109,3.371 0.736,0.147 10 *1: for LHD 3.372,3.477 4.155,3.624 0.783,0.147 10 *2: for RHD

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


e.

Read the value displayed on the tester.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.

U158932E01
1.01,1.928 1.159,2.087 0.149,0.159 10 *1 1.367,1.462 1.554,1.621 0.187,0.159 10 E2 1.267,1.157 1.567,1.316 0.299,0.159 10 THA 2.528,1.462 2.919,1.621 0.391,0.159 10 ETHA 2.528,1.157 2.828,1.316 0.299,0.159 10 THA 2.834,1.928 2.983,2.087 0.149,0.159 10 *2 4.078,0.265 4.227,0.424 0.149,0.159 10 *a 4.653,2.367 4.952,2.526 0.299,0.159 10 THA 5.112,1.926 4.856,2.354 false 5.444,2.367 5.635,2.526 0.192,0.159 10 E2 5.227,1.926 5.483,2.354 false 4.176,1.791 4.448,1.947 0.272,0.156 10 C21


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


g.

Read the value displayed on the tester.

Standard value:

140°C (284°F)


Text in Illustration
*1 Mass Air Flow Meter Sub-assembly *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C21-1 (THA) - C10-90 (THA) Always Below 1 Ω
C21-2 (E2) - C10-122 (ETHA) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C21-1 (THA) - C9-90 (THA) Always Below 1 Ω
C21-2 (E2) - C9-122 (ETHA) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255925E01
0.662,0.158 0.817,0.311 0.155,0.154 10 *1 2.57,0.158 2.725,0.311 0.155,0.154 10 *2 2.226,0.805 2.525,0.958 0.299,0.154 10 THA 2.226,1.183 2.615,1.336 0.389,0.154 10 ETHA

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Mass Air Flow Meter Sub-assembly
*2 ECM

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C21-1 (THA) or C10-90 (THA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C21-1 (THA) or C9-90 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR