Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer measures the engine off soak time, which is the time elapsed after the power switch has been turned off. The ECM uses the engine off soak time to monitor some systems for malfunction detection.

If necessary, the soak timer may activate the ECM to perform certain malfunction checks that can only be performed after the engine stopped. The soak timer is built into the ECM.

DTC No. DTC Detection Condition Trouble Area
P2610 ECM internal malfunction (2 trip detection logic). ECM

A275902E01
4.679,0.585 5.078,0.741 0.399,0.156 10 IGSW 5.833,4.333 6.197,4.489 0.364,0.156 10 ECM 5.198,1.301 5.930,1.610 0.732,0.309 10 Soak Timer IC 5.226,2.617 5.887,2.945 0.661,0.328 10 Power Source IC 5.198,3.422 5.937,3.745 0.739,0.323 10 Main Relay Control IC 3.577,0.826 4.246,0.976 0.669,0.151 10 IG2 NO. 2 4.679,2.767 4.905,2.936 0.225,0.170 10 +B 4.679,3.572 5.113,3.728 0.434,0.156 10 MREL 2.602,1.392 2.851,1.548 0.248,0.156 10 IG2 1.34,0.826 1.626,0.988 0.286,0.163 10 IG2 0.629,4.211 1.340,4.532 0.711,0.321 10 Auxiliary Battery 2.432,3.963 3.084,4.119 0.652,0.156 10 EFI-MAIN 2.3,1.942 2.692,2.098 0.392,0.156 10 IG2D 2.243,2.262 3.598,2.658 1.355,0.395 10 Power Management Control ECU 0.477,3.736 1.102,3.892 0.625,0.156 10 MAIN 1.351,3.404 2.036,3.560 0.685,0.156 10 EFI-MAIN 0.477,3.189 1.102,3.345 0.625,0.156 10 P/I

MONITOR DESCRIPTION

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 minutes or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2610.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and wait for 10 minutes or more.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.


k.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END