Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2C-247  Drive Motor "A" Temperature Sensor Circuit Low  P0A2D-249  Drive Motor "A" Temperature Sensor Circuit High  


DESCRIPTION

Refer to the description for DTC P0A2B-250 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A2C 247 Short or short to GND in the motor temperature sensor circuit
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


P0A2D 249 Open or short to +B in the motor temperature sensor circuit

HINT:

After confirming that DTC P0A2C-247 or P0A2D-249 is output, use the intelligent tester to check "Motor Temp No1" in the hybrid vehicle control ECU Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND


WIRING DIAGRAM

A407382E21
2.302,1.938 2.76,2.135 0.458,0.198 10 false 1 1.802,1.938 2.563,2.26 0.76,0.323 10 false MMTG 1.906,1.188 2.667,1.51 0.76,0.323 10 false MMT 2.302,1.188 2.76,1.385 0.458,0.198 10 false 2 0.24,2.667 1,2.99 0.76,0.323 10 false C25 0.26,2.844 2.458,3.521 2.198,0.677 10 false Hybrid Vehicle Transaxle Assembly (Motor Temperature Sensor) 2.552,2.667 4.563,3.521 2.01,0.854 10 false No. 1 Engine Room Relay Block Assembly Connector 2.542,2.5 3.302,2.823 0.76,0.323 10 false CA1 3.042,1.177 3.802,1.5 0.76,0.323 10 false 10 3.042,1.938 3.802,2.26 0.76,0.323 10 false 21 3.688,1.938 4.448,2.26 0.76,0.323 10 false 21 3.677,1.177 4.438,1.5 0.76,0.323 10 false 10 4.615,1.188 5.375,1.51 0.76,0.323 10 false 24 4.885,1.188 5.646,1.51 0.76,0.323 10 false MMT 4.625,1.948 5.385,2.271 0.76,0.323 10 false 23 4.875,1.938 5.635,2.26 0.76,0.323 10 false MMTG 4.948,2.688 5.708,3.01 0.76,0.323 10 false A71 4.938,2.833 6.646,3.51 1.708,0.677 10 false Hybrid Vehicle Control ECU 5.958,1.302 6.719,1.625 0.76,0.323 10 false ADC

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.
A279820C03
0.156,0.115 0.469,0.313 0.313,0.198 12 false *A 0.167,2.469 0.479,2.667 0.313,0.198 12 false *B
*A for LHD
*B for RHD


Check the connection condition of the Hybrid vehicle control ECU connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)
a.
A267573N05
2.208,0.979 2.583,1.208 0.375,0.229 2.26,1 2.552,1.188 0.292,0.188 10 true C25

Check the connection condition of the C25 motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO1)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.


d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.
A267573N05
2.208,0.979 2.583,1.208 0.375,0.229 2.26,1 2.552,1.188 0.292,0.188 10 true C25

Disconnect the C25 motor temperature sensor connector.


b.
A397756C03
1.448,0.115 1.885,0.365 0.438,0.25 1.146,1.708 1.49,1.229 true 2.292,1.708 1.927,1.219 true 0.542,0.302 0.854,0.458 0.313,0.156 10 false *a 2.125,1.74 2.604,1.948 0.479,0.208 10 false MMTG 0.979,1.76 1.438,1.958 0.458,0.198 10 false MMT 1.531,0.156 2.146,0.354 0.615,0.198 10 false C25
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-2 (MMT) - C25-1 (MMTG) Power switch off 0.3436 to 1442 kΩ


HINT:

The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C25 motor temperature sensor connector.



OK

6.INSPECT HYBRID VEHICLE CONTROL ECU

NG

6.INSPECT HYBRID VEHICLE CONTROL ECU
a.
A395365C07
0.594,0.938 1.021,1.219 0.427,0.281 0.479,2.25 0.729,1.844 false 1.167,2.281 0.781,1.844 false 0.688,0.99 1.146,1.188 0.458,0.198 10 false A71 0.979,2.313 1.594,2.51 0.615,0.198 10 false MMTG 0.281,2.302 0.896,2.5 0.615,0.198 10 false MMT 0.115,0.25 0.427,0.406 0.313,0.156 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Connect terminals 24 (MMT) and 23 (MMTG) of connector A71 of the hybrid vehicle control ECU.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.


e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No1 Terminals MMT and MMTG connected.
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.
A267573N01
2.208,0.979 2.583,1.208 0.375,0.229 2.26,1 2.552,1.188 0.292,0.188 10 true C25

Disconnect the C25 motor temperature sensor connector.


b.
A397756C03
1.448,0.115 1.885,0.365 0.438,0.25 1.146,1.708 1.49,1.229 true 2.292,1.708 1.927,1.219 true 0.542,0.302 0.854,0.458 0.313,0.156 10 false *a 2.125,1.74 2.604,1.948 0.479,0.208 10 false MMTG 0.979,1.76 1.438,1.958 0.458,0.198 10 false MMT 1.531,0.156 2.146,0.354 0.615,0.198 10 false C25
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-2 (MMT) - C25-1 (MMTG) Power switch off 0.3436 to 1442 kΩ


HINT:

The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C25 motor temperature sensor connector.



OK

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the C25 motor temperature sensor connector.


b.

Disconnect the A71 hybrid vehicle control ECU connector.


c.
A379315C04
1.25,3.75 1.667,4 0.417,0.25 0.583,0.917 0.958,1.167 0.375,0.25 1.271,1.677 1.531,1.135 false 2.094,1.688 1.708,1.135 false 0.604,4.292 0.74,3.875 false 1.146,4.271 0.781,3.875 false 0.656,0.958 0.969,1.156 0.313,0.198 10 false C25 1.323,3.792 1.635,3.99 0.313,0.198 10 false A71 0.188,1.969 0.5,2.167 0.313,0.198 10 false *b 0.188,0.219 0.5,0.417 0.313,0.198 10 false *a 1.969,1.719 2.385,1.958 0.417,0.24 10 false MMT 0.469,4.292 0.885,4.531 0.417,0.24 10 false MMT 1,4.292 1.469,4.531 0.469,0.24 10 false MMTG 1.063,1.698 1.531,1.938 0.469,0.24 10 false MMTG
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
C25-2 (MMT) - A71-24 (MMT) Power switch off Below 1 Ω
C25-1 (MMTG) - A71-23 (MMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
C25-2 (MMT) or A71-24 (MMT) - Body ground and other terminals Power switch off 10 kΩ or higher
C25-1 (MMTG) or A71-23 (MMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A71 hybrid vehicle control ECU connector.


e.

Reconnect the C25 motor temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR