The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in MG2 temperature. The lower the MG2 temperature, the higher the thermistor resistance. Conversely, the higher the MG2 temperature, the lower the resistance.
The term "drive motor A" indicates MG2.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A2B | 250 | Motor temperature sensor output does not increase under conditions in which the value should increase, or output does not decrease under conditions in which the value should decrease. | ·
Wire harness or connector ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
| P0A2E | 248 | Unusual sudden change in motor temperature sensor output occurs and the condition continues, or unusual sudden change in motor temperature sensor output occurs repeatedly. |
If DTC P0A2B-250 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Drive the vehicle (stop and go driving) on urban roads for approximately 5 minutes.
If the Data List item "Motor Temp No1" shows both increases and decreases in temperature, suspected areas indicated by this DTC are not malfunctioning.
If DTC P0A2E-248 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (READY) and wait for 30 seconds or more.
Drive the vehicle for approximately 5 minutes according to the freeze frame data items "Vehicle Spd", "Motor Temp No1" and "Motor Temp No2".
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Disconnect the A71 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-24 (MMT) - A38-23 (MMTG) | Power switch off | 0.3436 to 1442 kΩ |
Reconnect the A71 hybrid vehicle control ECU connector.
OK
NG
Check the connection condition of the engine room relay block No. 1 CA1connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Disconnect the CA1 engine rool relay block No. 1 connector.
Disconnect the A71 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.
| *a | Front view of wire harness connector
(to Engine rool relay block No. 1) |
*b | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| CA1-10 (MMT) - A71-24 (MMT) | Power switch off | Below 1 Ω |
| CA1-21 (MMTG) - A71-23 (MMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| CA1-10 (MMT) - Other terminals | Power switch off | 10 kΩ or higher |
| CA10-21 (MMTG) - Other terminals | Power switch off | 10 kΩ or higher |
Reconnect the A71 hybrid vehicle control ECU connector.
Reconnect the CA1 engine rool relay block No. 1 connector.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Disconnect the CA1 engine room relay block No. 1 connector.
Disconnect the C25 motor temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.
| *a | Front view of wire harness connector
(to Motor Temperature Sensor) |
*b | Front view of wire harness connector
(to Engine Rool Relay Block No. 1) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| CA1-10 (MMT) - C25-2 (MMT) | Power switch off | Below 1 Ω |
| CA1-21 (MMTG) - C25-1 (MMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| CA1-10 (MMT) - Other terminals | Power switch off | 10 kΩ or higher |
| CA1-21 (MMTG) - Other terminals | Power switch off | 10 kΩ or higher |
Reconnect the C25 motor temperature sensor connector.
Reconnect the CA1 engine room relay block No. 1 connector.
OK
NG
Disconnect the CA1 engine rool relay block No. 1 connector.
| *a | Front view of wire harness connector
(to Engine Rool Relay Block No. 1) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| CA1-10 (MMT) - CA1-21 (MMTG) | Power switch off | 0.3436 to 1442 kΩ |
Reconnect the CA1 engine rool relay block No. 1 connector.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247
| Proceed to |
|---|
| OK |
| NG |
OK
NG