Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A37-260  Generator Temperature Sensor Circuit Range / Performance  P0A3A-258  Generator Temperature Sensor Circuit Intermittent  


DESCRIPTION

The resistance of the thermistor built into the generator temperature sensor changes in accordance with changes in MG1 temperature. The lower the MG1 temperature, the higher the thermistor resistance. Conversely, the higher the MG1 temperature, the lower the resistance.

A172965E06
2.044,0.334 2.299,0.484 0.255,0.151 10 120 2.044,0.477 2.299,0.628 0.255,0.151 10 110 2.044,0.617 2.299,0.768 0.255,0.151 10 100 2.119,0.747 2.299,0.898 0.180,0.151 10 90 2.126,0.88 2.299,1.031 0.173,0.151 10 80 2.119,1.017 2.299,1.167 0.180,0.151 10 70 2.119,1.146 2.299,1.297 0.180,0.151 10 60 2.119,1.279 2.299,1.430 0.180,0.151 10 50 2.119,1.419 2.299,1.570 0.180,0.151 10 40 2.119,1.559 2.299,1.710 0.180,0.151 10 30 2.119,1.693 2.299,1.843 0.180,0.151 10 20 2.119,1.833 2.299,1.983 0.180,0.151 10 10 0.9,1.055 1.934,1.206 1.034,0.151 10 Resistance (kΩ) 5.481,2.239 6.967,2.390 1.486,0.151 10 Temperature (°C (°F )) 2.312,2.169 2.492,2.320 0.180,0.151 10 10 2.256,2.319 2.536,2.470 0.281,0.151 10 (50) 2.725,2.319 3.006,2.470 0.281,0.151 10 (59) 3.18,2.319 3.461,2.470 0.281,0.151 10 (68) 3.646,2.319 3.927,2.470 0.281,0.151 10 (77) 4.108,2.319 4.389,2.470 0.281,0.151 10 (86) 4.557,2.319 4.838,2.470 0.281,0.151 10 (95) 4.965,2.319 5.309,2.470 0.343,0.151 10 (104) 2.753,2.169 2.933,2.320 0.180,0.151 10 15 3.229,2.169 3.409,2.320 0.180,0.151 10 20 3.695,2.169 3.875,2.320 0.180,0.151 10 25 4.143,2.169 4.324,2.320 0.180,0.151 10 30 4.595,2.169 4.808,2.320 0.213,0.151 10 35 5.047,2.169 5.325,2.320 0.277,0.151 10 40 2.193,1.962 2.300,2.113 0.107,0.151 10 0

DTC No. INF Code DTC Detection Condition Trouble Area
P0A37 260 Generator temperature sensor output does not increase in which the value should increase, or output does not decrease under conditions in which the value should decrease.
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly (Generator temperature sensor)


P0A3A 258 Unusual sudden change in generator temperature sensor output occurs and the condition continues, or unusual sudden change in generator temperature sensor output occurs repeatedly.

WIRING DIAGRAM

A407382E24
2.302,1.177 2.76,1.375 0.458,0.198 10 false 4 1.802,1.927 2.563,2.25 0.76,0.323 10 false GMTG 1.906,1.177 2.667,1.5 0.76,0.323 10 false GMT 2.302,1.927 2.76,2.125 0.458,0.198 10 false 8 0.146,2.688 0.906,3.01 0.76,0.323 10 false C24 0.167,2.844 2.385,3.604 2.219,0.76 10 false Hybrid Vehicle Transaxle Assembly (Generator Temperature Sensor) 2.552,2.667 4.563,3.521 2.01,0.854 10 false No. 1 Engine Room Relay Block Assembly Connector 2.531,2.51 3.292,2.833 0.76,0.323 10 false CA1 3.042,1.177 3.802,1.5 0.76,0.323 10 false 22 3.042,1.938 3.802,2.26 0.76,0.323 10 false 11 3.677,1.938 4.438,2.26 0.76,0.323 10 false 11 3.677,1.177 4.438,1.5 0.76,0.323 10 false 22 4.615,1.167 5.375,1.49 0.76,0.323 10 false 26 4.865,1.167 5.625,1.49 0.76,0.323 10 false GMT 4.635,1.927 5.396,2.25 0.76,0.323 10 false 27 4.875,1.917 5.635,2.24 0.76,0.323 10 false GMTG 4.865,2.667 5.625,2.99 0.76,0.323 10 false A38 4.865,2.844 6.573,3.521 1.708,0.677 10 false Power Management Control ECU 5.958,1.302 6.719,1.625 0.76,0.323 10 false ADC

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0A37-260 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Drive the vehicle (stop and go driving) on urban roads for approximately 5 minutes.

If the Data List item "Motor Temp No2" shows both increases and decreases in temperature, suspected areas indicated by this DTC are not malfunctioning.


·

If DTC P0A3A-258 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (READY) and wait for 30 seconds or more.

(b)

Drive the vehicle for approximately 5 minutes according to the freeze frame data items "Vehicle Spd", "Inverter Coolant Water Temperature", "Motor Temp No1" and "Motor Temp No2".




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A448677C02
0.094,2.365 0.448,2.594 0.354,0.229 0.594,2.51 0.49,2.958 true 0.646,2.51 1.052,2.969 true 0.125,0.344 0.438,0.542 0.313,0.198 10 false *a 0.156,2.406 0.615,2.604 0.458,0.198 10 false A38 0.938,3 1.396,3.198 0.458,0.198 10 false GMT 0.26,3.01 0.875,3.208 0.615,0.198 10 false GMTG
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the A38 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-26 (GMT) - A38-27 (GMTG) Power switch off 0.3436 to 1442 kΩ



c.

Reconnect the A38 power management control ECU connector.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK NO. 1)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK NO. 1)
a.

Disconnect the CA1 engine rool relay block No. 1 connector.


b.

Disconnect the A38 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


A448678C07
4.781,1.708 5.167,2 0.385,0.292 0.302,1.313 0.688,1.604 0.385,0.292 4.208,1.927 3.99,2.313 true 4.26,1.938 4.667,2.271 true 1.229,1.333 1.688,0.74 true 1.229,1.594 1.594,2.198 true 0.542,0.219 0.854,0.417 0.313,0.198 10 false *a 3.625,0.229 3.938,0.427 0.313,0.198 10 false *b 0.396,1.375 0.854,1.573 0.458,0.198 10 false CA1 4.854,1.792 5.313,1.99 0.458,0.198 10 false A38 4.583,2.333 5.198,2.531 0.615,0.198 10 false GMT 1.583,0.552 2.042,0.75 0.458,0.198 10 false GMTG 3.833,2.354 4.292,2.552 0.458,0.198 10 false GMTG 1.5,2.26 2.115,2.458 0.615,0.198 10 false GMT
*a Front view of wire harness connector
(to Engine rool relay block No. 1)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
CA1-22 (GMT) - A38-26 (GMT) Power switch off Below 1 Ω
CA1-11 (GMTG) - A38-27 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
CA1-22 (GMT) - Other terminals Power switch off 10 kΩ or higher
CA10-11 (GMTG) - Other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A38 power management control ECU connector.


e.

Reconnect the CA1 engine rool relay block No. 1 connector.



OK

5.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A38-257

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK NO. 1 - HYBRID VEHICLE TRANSAXLE ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK NO. 1 - HYBRID VEHICLE TRANSAXLE ASSEMBLY)
a.

Disconnect the CA1 engine room relay block No. 1 connector.


b.

Disconnect the C24 generator temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


A448681C01
3.49,1.292 3.865,1.563 0.375,0.271 0.542,1.24 0.917,1.51 0.375,0.271 1.844,1.26 2.094,0.677 true 2.167,2.021 1.833,1.438 true 5.573,1.375 5.781,0.771 true 5.563,1.656 5.75,2.052 true 0.573,0.5 0.885,0.698 0.313,0.198 10 false *a 3.729,0.427 4.042,0.625 0.313,0.198 10 false *b 0.615,1.302 1.073,1.5 0.458,0.198 10 false C24 5.698,0.604 6.313,0.802 0.615,0.198 10 false GMTG 2.01,0.479 2.625,0.677 0.615,0.198 10 false GMT 2.021,2.094 2.635,2.292 0.615,0.198 10 false GMTG 5.677,2.115 6.292,2.313 0.615,0.198 10 false GMT 3.573,1.344 4.031,1.542 0.458,0.198 10 false CA1
*a Front view of wire harness connector
(to Generator Temperature Sensor)
*b Front view of wire harness connector
(to Engine Rool Relay Block No. 1)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
CA1-22 (GMT) - C24-4 (GMT) Power switch off Below 1 Ω
CA1-11 (GMTG) - C24-8 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
CA1-22 (GMT) - Other terminals Power switch off 10 kΩ or higher
CA1-11 (GMTG) - Other terminals Power switch off 10 kΩ or higher



d.

Reconnect the C24 generator temperature sensor connector.


e.

Reconnect the CA1 engine room relay block No. 1 connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.

Disconnect the CA1 engine rool relay block No. 1 connector.


b.
A448674C01
0.115,0.99 0.521,1.25 0.406,0.26 2.604,1.104 2.771,0.458 true 2.604,1.417 2.74,1.792 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.198,1.052 0.656,1.25 0.458,0.198 10 false CA1 2.688,1.823 3.146,2.021 0.458,0.198 10 false GMT 2.635,0.271 3.25,0.469 0.615,0.198 10 false GMTG
*a Front view of wire harness connector
(to Engine Rool Relay Block No. 1)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
CA1-22 (GMT) - CA1-11 (GMTG) Power switch off 0.3436 to 1442 kΩ



c.

Reconnect the CA1 engine rool relay block No. 1 connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
8.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG