Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-279  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

If an overvoltage occurs in the motor inverter or generator inverter, the MG ECU detects it and transmits this information to the power management control ECU.

HINT:

The term "drive motor A" indicates MG2.


DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 279 Motor inverter overvoltage signal detection (overvoltage (inverter malfunction)) Inverter with converter assembly

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

With the vehicle engine stopped, the power switch on (READY) and the shift lever in P, depress the accelerator pedal to start the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A78-279 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A78-266, 267, 287, 505, 506, 565, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-325, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A93-346 Inverter Cooling System Performance
P0A94-554, 555, 556, 585, 587, 589, 590 DC / DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3004-803 High Voltage Power Resource
P314A-828 Inverter Coolant Pump Speed Signal

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A78-279 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

CONNECT SECURELY